Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 16

Страница: 16 / 272

Description of device parameters

Proline Promag 300 Modbus RS485

Hauser

Format display

Navigation

 Expert → System → Display → Format display (0098)

Prerequisite

A local display is provided.

Description

Use this function to select how the measured value is shown on the local display.

Selection

• 1 value, max.

• Bargr. + 1 value

• 2 values

• Val. large+2val.

• 4 values

Factory setting

1 value, max.

Additional information

Description

The display format (size, bar graph etc.) and number of measured values displayed

simultaneously (1 to 4) can be configured. This setting only applies to normal operation.

• The

Value 1 display

parameter (→  18) to

Value 4 display

parameter

(→  23) are used to specify which measured values are shown on the local

display and in what order.

• If more measured values are specified than the display mode selected permits, then

the values alternate on the device display. The display time until the next change is

configured via the

Display interval

parameter (→  24).

Custody transfer mode

Only available for Promag H.

• Once the measuring device has been enabled for custody transfer mode, depending on

the custody transfer approval selected the display can switch between showing the

relevant information and the custody transfer counter.

• In addition, a padlock symbol appears in the header of the display ().

For detailed information on custody transfer mode, see the Special Documentation for

the device →  7

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды