Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 23

Страница: 23 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

Decimal places 3



Navigation

 Expert → System → Display → Decimal places 3 (0118)

Prerequisite

A measured value is specified in the

Value 3 display

parameter (→  21).

Description

Use this function to select the number of decimal places for measured value 3.

Selection

• x

• x.x

• x.xx

• x.xxx

• x.xxxx

Factory setting

x.xx

Additional information

Description

This setting does not affect the measuring or computational accuracy of the device.

The arrow displayed between the measured value and the unit indicates that the

device computes with more digits than are shown on the local display.

Value 4 display



Navigation

 Expert → System → Display → Value 4 display (0109)

Prerequisite

A local display is provided.

Description

Use this function to select one of the measured values to be shown on the local display.

Selection

For the picklist, see the

Value 2 display

parameter (→  20)

Factory setting

None

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды