Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 57

Страница: 57 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

Volume unit



Navigation

 Expert → Sensor → System units → Volume unit (0563)

Description

Use this function to select the unit for the volume.

Selection

SI units

• cm³

• dm³

• m³

• ml

• l

• hl

• Ml Mega

US units

• af

• ft³

• fl oz (us)

• gal (us)

• kgal (us)

• Mgal (us)

• bbl (us;oil)

• bbl (us;liq.)

• bbl (us;beer)

• bbl (us;tank)

Imperial units

• gal (imp)

• Mgal (imp)

• bbl (imp;beer)

• bbl (imp;oil)

Factory setting

Country-specific:

• m³

• gal (us)

Additional information

Selection

For an explanation of the abbreviated units: →  217

Customer-specific units

The unit for the customer-specific volume is specified in the

Volume text

parameter

(→  63).

Conductiv. unit



Navigation

 Expert → Sensor → System units → Conductiv. unit (0582)

Prerequisite

The

option is selected in the

Conduct. measur.

parameter (→  74) parameter.

Description

Use this function to select the unit for the conductivity.

Selection

SI units

• nS/cm

• µS/cm

• µS/m

• µS/mm

• mS/m

• mS/cm

• S/cm

• S/m

• kS/m

• MS/m

Factory setting

µS/cm

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды