Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 176

Страница: 176 / 272

Description of device parameters

Proline Promag 300 Modbus RS485

176

Hauser

Additional information

Display

Via the local display: the time stamp and corrective measures referring to the cause of

the diagnostic message can be accessed via the  key.

Examples

For the display format:

• F271 Main electronics

• F276 I/O module

Timestamp

Navigation



Expert → Diagnostics → Diagnostic list → Timestamp

Description

Displays the operating time when the diagnostic message with the second-highest priority

occurred.

User interface

Days (d), hours (h), minutes (m) and seconds (s)

Additional information

Display

The diagnostic message can be viewed via the

Diagnostics 2

parameter (→  175).

Example

For the display format:

24d12h13m00s

Diagnostics 3

Navigation

 Expert → Diagnostics → Diagnostic list → Diagnostics 3 (0694)

Description

Displays the current diagnostics message with the third-highest priority.

User interface

Symbol for diagnostic behavior, diagnostic code and short message.

Additional information

Display

Via the local display: the time stamp and corrective measures referring to the cause of

the diagnostic message can be accessed via the  key.

Examples

For the display format:

• F271 Main electronics

• F276 I/O module

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды