manualshive.com logo in svg

Eliet DZC600, Руководство пользователя

Поделиться
Скачать
Eliet DZC600 Скачать руководство пользователя страница 73

73

English

15.2 Hazard analysis 

Please find below a list of hazards and risks connected with transportation or operation of this 
overseeder. Take good notice of these dangers and avoid risks by following the instructions in 
the manual. Beware that risks are not limited to the operator: bystanders can be exposed as well. 
Ensure that bystanders are always kept at a safe distance.

•   Danger of flying debris during overseeding activities.
•   Injuries from flying debris from the outlet while the machine is being used without a collector. 
•   Injuries from flying debris while lifting the machine into transport mode.
•   Bruises or injuries when the machine is lowered, namely at the transfer point between 

transport mode and work mode.

•   Danger of cuts to the feet when engaging the blades with the machine locked in transport 

mode.

•   Injuries from contact with the blades when reaching under the machine.
•   Injuries from contact with the blades during deblocking, maintenance or cleaning activities.
•   Squeezing or jamming when the seed reservoir lid slams shut.
•   Reaching into the rotating drum in the seed reservoir introduces the risk of fractured or 

bruised fingers.

•   Reaching into chain drives when removing chain covers introduces the risk of fractured, 

entangled or severed fingers or limbs.

•   Reaching into belt drives when removing belt covers introduces the risk of fractured, 

entangled or severed fingers or limbs.

•   Spraining of feet or knee joints when lower limbs get stuck under the swivel caster or anti-

scalping roller. 

•   Injuries caused by the machine toppling over as a result of unsafe transport.
•   Physical injury can occur when traversing a terrain that cannot support the weight of the 

machine.

•   Heat exhaust or heat from the engine can cause scorching.
•   Rubbish build-up around the exhaust or poor cleansing of the engine creates a fire hazard.
•   Petrol spills also create a fire hazard.
•   Heavy inhalation of exhaust fumes can induce intoxication.
•   Air passages and the lungs are prone to irritation from breathing in dust particles produced 

during operation.

•   Hearing loss as a result of not wearing the proper ear plugs or hearing protection during 

operation.

•   Nerve damage or rheumatic disease can develop when exposed to the jarring for too long, 

without pausing for breaks.

•   Back problems caused by lifting the machine in an irresponsible way.
•   Risk of perforation of the skin or senses by the oil jet when a hydraulic component breaks.
• …
The list is not exhaustive and is only provided as information in relation to the operator’s safety. 

Содержание DZC600














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды