manualshive.com logo in svg

Eliet DZC600, Руководство пользователя

Поделиться
Скачать
Eliet DZC600 Скачать руководство пользователя страница 61

61

English

61

•  Re-attach the bolt once the belt has the correct tension.

After performing this maintenance, the belt covers can be remounted like they originally were.

Second belt drive (blade drive)

These belts can be tightened with a flat tensioning roller that is pulled against the back of the 

belt while pushing down the lever that engages the blades.  This belt drive transmits power 
to the blades and, thus, also carries the heaviest load.  It is also a belt transmission that is 
frequently switched on and off, and it is therefore subject to slippage. 

•  If the belt starts to make a squeaking sound, or if the lever resistance is too low, it is clear that 

the belt tensioning roller needs to be adjusted.

•  To re-tighten the belt, the first cover on the left-hand side of the machine needs to be removed 

(see  § “15.1 Removing the protective covers” on page 71).

•  You will know that you have reached the proper 

amount of tension if, just before fully pushing 
down the lever (with 20 mm to spare up to the 
handle), the belt tensioning roller (1) is already 
fully pressed against the belt. 

 •  If this is less than 20 mm, the force of pressure 

from the tensioning roller will need to be 
increased by adjusting the length of the starter 
cord. 

Содержание DZC600














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды