manualshive.com logo in svg

Eliet DZC600, Руководство пользователя

Поделиться
Скачать
Eliet DZC600 Скачать руководство пользователя страница 37

37

English

9.8  Fault diagnosis

9.8.1  The motor fails to start after idle periods

If the machine fails to start up after periods of inactivity, then this could be the result of any of 
the following causes:

a) No petrol
c) Stale petrol
d) Bad spark plug
e) Low on oil

Caution:

Before examining possible reasons for the fault, make sure the ON/OFF switch 
for the motor is turned to the OFF position.

a) No petrol

In  § “12.Storing the machine” on page 68 you are advised to remove any residual petrol 
before long term storage of the machine. If this slipped your mind, you may have forgotten 
to refill the machine. Check that the tank is adequately filled and refuel if necessary  (read § 
“9.4.2 

Refuelling” on page 28)

Let the starter motor run for a while after refuelling. Close the throttle (choke) - the petrol 
will now be sucked into the line. The motor will start running as soon as the carburettor has 
filled. 

c) Stale petrol

Petrol has a limited shelf life. Petrol that has been sitting in petrol tank for more than a few 
months can cause starter problems. It also smells totally different than fresh petrol. 
Pump out the contents of the fuel tank and refuel with fresh petrol (read § “9.4.2  Refuel-
ling” on page 28) 

Caution:

 

Always exercise precaution. Even stale petrol can still be incredibly flammable.

Содержание DZC600














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды