manualshive.com logo in svg

Eliet DZC600, Руководство пользователя

Поделиться
Скачать
Eliet DZC600 Скачать руководство пользователя страница 51

51

English

•  Put the DZC 600 into the easy clean (option) to change the oil.

•  Keep a 2 litre receptacle nearby before unscrewing the plug.
•  Clean the area around the oil filler cap on the other side of the engine and unscrew the cap, 

allowing the crankcase to vent while emptying the tank. 

•   Now unscrew the drainage plug. Use a 22 mm wrench. 
•  Empty the full contents (1.1 L) from the engine.  Make sure that all the oil is properly collected 

in the receptacle.

•  Tilt the machine forward again.
•  Reposition the drainage plug and tighten it.  (Attention: don’t tighten it too much: the engine 

base might crack.)   

•  Wipe away any spilled oil with a clean cloth.
•   Refill the engine with new oil through the front filler 

cap. 

•   Gradually add the required oil, approx. 1.1 litres, until 

it reaches the brim of the filler hole. 

 •  Reposition and tighten the filler cap after refilling 

and wipe away any spilled oil.

highest level

lowest level

Содержание DZC600














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды