background image

14.01.2019

54/185

5.7.3 Setpoint reduction above medium pressure

The function is only active when 

MP const.valve

 is set to "

No

" (menu 3-1). This function is deactivated when 

ECO operation is running.

A minimum difference between the medium pressure actual value and the suction pressure setpoint is 
maintained with this function. The desired pressure difference can be configured with the parameter 

Min MP/LP 

Diff 

(menu 3-3). The suction pressure setpoint is reduced with falling medium pressure that results in loading of 

compressors and thus in increase of the medium pressure to the desired pressure level.

5.7.4 Medium pressure maintenance

The medium pressure can be maintained using a 

pressure maintenance valve

 or by opening the 

HP valve

 . The 

operating mode can be set with the parameter 

MP const.valve 

(menu 3-1).

Medium pressure maintenance via pressure maintenance valve

If the medium pressure valve is closed (0 Volt control signal) and the medium pressure falls below the medium 
pressure setpoint minus a maximum pressure difference, a pressure maintenance valve is activated.
The pressure maintenance valve is switched off again when the medium pressure has reached the MP setpoint 
minus 0.5 bar. The maximum pressure difference can be configured.
The following is a graphic representation of the pressure maintenance valve control:

The pressure maintenance valve is switched off for a fast unload. The setpoints for the MP regulation or control 
of the pressure maintenance valve 

Setp. MP

 and 

MP dif.

 are configured using the menu 3-2-3.

The function is only active when the suction gas sensor 

OH-C

 is available. As long as MP setpoint 

reduction is active due to " 

Low Superheat-C

", no setpoint increase due to " 

Low Superheat-P

" can take 

place.

Содержание VS 3015 C


























































































































































































Отзывы: