9711-26020-0001
Exp o rt Co n tro lle d – S e e P a g e 3
Rev D
SECTION 2
GETTING TO KNOW YOUR ARMOR X10GX
Page 56 of 234
ARMOR X10gx Tablet Computer
Fingerprint
Scanner
AuthenTec® AES1660 fingerprint sensor with TrueNav™ cursor and menu navigation;
Interface: USB 2.0 full speed, fully encrypted, suspend and remote wakeup, selective suspend
support;
Camera
2.0 mega-pixel camera, SXGA 4:3 format, 1280 x 1024 pixels resolution, F2.0 lens, auto-focus
with enable/disable, still pin interface for high speed still image capture; Sensitivity: 0.7 V/lux-sec
minimum
Frame rates: (ambient light @ 250 nits): SXGA (1280 x 1024) - 25 fps, SVGA (800 x 600) - 30
fps, VGA (640 x 480) - 35+ fps; Interface: USB 2.0 with selective suspend; Output formats:
JPEG (still), MPEG (movie)
Expansion Slots
Single ExpressCard® 26-pin 34/54 mm slot or optional (factory installed) single PC/PCMCIA
Type I/II card slot
Single ISO/IEC 7810 compatible Smart Card slot. Supports ISO/IEC 7816 interface protocol and
PC/SC specification version 2.0.1.5. Driver software certifiable to Microsoft WHQL, EMV 2000,
USB CCIE and ISO 7816 standards (Door designed to close with standard card inserted.)
Single Secure Digital (SD) card reader accepting industry standard cards with capacities up to
32GB.
TPM Module
Support
Supports installation of a TPM controller module that meets the requirements of the Trusted
Computing Group (TCG) Trusted Platform Module Specification 1.2. Supports the TPM 1.2
solutions provided by Intel and Infineon.
External
Interface
One (1) Power Input jack: 12.0 – 28VDC (16VDC nominal); can be powered through external
DC power jack or input power pins on the docking connector
Three (3) USB 2.0 external port connectors (three additional USB ports available through
optional docking device); supports externally powered 4-port hub
One (1) 10/100/100 Gigabit Ethernet LAN RJ45 external connector
One (1) external RS-232 serial port D-Sub 9-pin connector
One (1) DisplayPort video output connector
One (1) headphone/microphone/external speaker jack
Docking
Interface
One (1) Power Input : 12.0 – 28VDC (16VDC nominal)
One (1) Power Output: 5VDC ± 5% to power downstream devices
Two (2) ground/open discrete GPIO inputs pulled up to 5V inside the X10gx and wired to GPIO
on the EC controller to allow for custom applications requiring discrete input; source impedance
<10k and no more than 100k; both pins ESD protected
Three (3) USB 2.0 ports
Six (6) Flex I/O bi-directional discrete wired directly to the Flexboard inside the X10gx to be used
for custom applications; all pins are ESD protected
One (1) VGA port
One (1) RS-232 serial port
One (1) RJ-45 Ethernet port
One (1) microphone input line
One (1) audio jack with Left and right channel audio outputs
Two (2) discrete coaxial RF connectors - one for an external GPS antenna and one for an
external wireless antenna; 50ohm female BMMA-style push on/pull off connectors
Flexspace™
Interface
Flexible I/O for custom circuit cards and modules; space available in the rear flexspace
compartment and the right side panel. Refer to the “ARMOR X10gx Flexspace Utilization
Guide”, P/N 9711-26020-0100 for detailed information.
Power
Internal: One or two 11.1 VDC 2400 mAh lithium-ion rechargeable batteries; approximately 4
