DEC DECstation 5000 Model 100 Series Скачать руководство пользователя страница 262

Страница: 262 / 269

Table G-2 (Cont.).

Minor Error and Status Error Codes

Minor code

Meaning

043e

Unable to handle empty circular buffer here.

043f

No more unused I/O available.

0440

No more unused I/O-control blocks available.

0441

Invalid file name encountered by filename parser.

0442

Corrupted job pointer.

0443

Opening: Required controller not found.

0444

Opening: Required port driver or controller not found.

0445

Opening: Not a file system.

0446

Invalid read address size specified.

0447

Read: Block alignment error.

0448

Read: Unable to locate job for file descriptor.

044a

One or both of the fds received by _is_samedev is corrupted.

044b

The how–2 seek option is unsupported.

044c

Invalid seek option was specified.

044d

Unable to locate job corresponding to file descriptor.

044e

Attempted to find driver data for unknown device.

044f

Opening: Unsupported file-sys type.

0450

The never-to-be-called I/O stub was called.

0451

Write: Block alignment error occurred.

0452

Invalid write address size was specified.

0454

Invalid MOP message code.

0455

MOP load number mismatch for memory load message.

0456

MOP load number mismatch for parameter load message.

0457

MOP file name is too long.

0458

MOP receive message failed.

0459

MOP receive message timeout occurred.

045a

MOP send message failed.

045b

No ioctls are supported by MOP.

0456

MOP I/O function error.

045d

Password has less than 8 or more than 32 characters.

(continued on next page)

G–6

Console Status and Error Message Codes Generated by Version PDE3 ROM Chips

Содержание DECstation 5000 Model 100 Series














































































































































































































































































Результаты поиска

Содержание DECstation 5000 Model 100 Series

Отзывы:

Похожие инструкции для DECstation 5000 Model 100 Series

Бренды по названию

Популярные бренды

DEC DECstation 5000 Model 100 Series, Руководство по обслуживанию

Результаты поиска

Содержание DECstation 5000 Model 100 Series

Отзывы:

Похожие инструкции для DECstation 5000 Model 100 Series

Бренды по названию

Популярные бренды