DEC DECstation 5000 Model 100 Series Скачать руководство пользователя страница 212

Страница: 212 / 269

Serial Line Silo Alarm Test

The serial line silo alarm test checks the serial line controller’s
ability to generate a silo alarm interrupt.

To run this test, type t f42 P1 P2 and press Return.

Serial line silo alarm test error messages

Table F-4 describes the parameters in serial line silo alarm test
commands and error messages.

Table F-5 lists the error codes found in serial line silo alarm
error messages.

Table F-4.

Serial Line Silo Alarm Test Parameters

Parameter

Description

Specifies the test’s loopback setting. Specify 0 for internal
loopback; specify 1 for external loopback.

Specifies the serial line to be tested.

Specify 0 to test the keyboard.

Specify 1 to test the mouse.

Specify 2 to test the right communications line .

Specify 3 to test the left communications line.

Actual value in register named in the subtest.

Expected value in register named in the subtest.

Table F-5.

Serial Line Silo Alarm Test Error Codes

Error Code

Meaning

Silo alarm test failed.

Unexpected silo alarm interrupt occurred.

Silo alarm timeout error occurred.

No silo alarm interrupt occurred.

F–6

Test Commands and Messages Produced by Version PDE3 ROM Chips

Содержание DECstation 5000 Model 100 Series














































































































































































































































































Результаты поиска

Содержание DECstation 5000 Model 100 Series

Отзывы:

DEC DECstation 5000 Model 100 Series, Руководство по обслуживанию, Страница: 212 / 269

Результаты поиска

Содержание DECstation 5000 Model 100 Series

Отзывы: