manualshive.com logo in svg

DEC DECstation 5000 Model 100 Series, Руководство по обслуживанию

Поделиться
Скачать
DEC DECstation 5000 Model 100 Series Скачать руководство пользователя страница 26

System Unit Connectors

The system unit connectors, shown in Figure 1-4, have the
following purposes:

The power connector connects the system unit power supply
and the system unit power cord.

The monitor-to-system-unit connector provides electric
power to the monitor power cord.

The ThinWire Ethernet connector links the system unit to
a ThinWire Ethernet.

The SCSI connector connects the base system SCSI
controller to a chain of external drives.

The keyboard-mouse connector links the system unit to the
keyboard-mouse cable.

The communications connectors provide printer, modem,
and console terminal connections. If there is a console
terminal, the terminal usually connects to the left
communications connector.

The option module connectors connect option modules to
external hardware. The number printed above each option
module connector is the slot number for any option module
in that slot.

A Look at DECstation/DECsystem 5000 Model 200 Hardware

1–7

Содержание DECstation 5000 Model 100 Series














































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды