DEC DECstation 5000 Model 100 Series Скачать руководство пользователя страница 217

Страница: 217 / 269

Keyboard and Mouse Test

The keyboard and mouse test checks the keyboard, mouse and
serial line controller on the system module.

To run a keyboard and mouse test, type t f41 P1 P2 and press
Return.

Keyboard and mouse test parameters and error messages

Table F-14 lists the parameters used in keyboard and mouse
test commands and error messages.

Table F-15 lists the error codes used in keyboard and mouse
test error messages.

Table F-14.

Keyboard and Mouse Test Parameters

Parameter

Description

Specifies which item to test.

Replace P1 with 0 to test the keyboard.

Replace P1 with 1 to test the mouse.

Specifies whether to run an internal or external loopback
test.

Replace P2 with 0 to run an internal loopback test.

Replace P2 with 1 to run an external loopback test.

Actual value in register named in the subtest.

Expected value in register named in subtest.

Four characters the self-test returned.

Character the controller sent to the device to start the test.

Test Commands and Messages Produced by Version PDE3 ROM Chips

F–11

Содержание DECstation 5000 Model 100 Series














































































































































































































































































Результаты поиска

Содержание DECstation 5000 Model 100 Series

Отзывы:

Похожие инструкции для DECstation 5000 Model 100 Series

Бренды по названию

Популярные бренды

DEC DECstation 5000 Model 100 Series, Руководство по обслуживанию

Результаты поиска

Содержание DECstation 5000 Model 100 Series

Отзывы:

Похожие инструкции для DECstation 5000 Model 100 Series

Бренды по названию

Популярные бренды