manualshive.com logo in svg

DEC DECstation 5000 Model 100 Series, Руководство по обслуживанию

Поделиться
Скачать
DEC DECstation 5000 Model 100 Series Скачать руководство пользователя страница 205

Booting the System Software

Use the boot command to boot the system software. Type boot
[ -ffile] [-n] [arg...] and press Return.

The boot command loads the file that contains the operating
system.

To boot a specific file, replace the optional -f file parameter
with the name of the file you want to use. If you do not
specify -f file, the system loads the file specified by the
bootpath environment variable.

The file parameter has the format

dev([controller][,unit-number] [,partition-number])[filename]

where

dev represents the device from which you are booting
the operating system. Typical devices are rz for a hard
disk, tz for a tape, and mop for a network. Typing mop
nullifies the other arguments in the list, so that file
takes the

controller represents the ID number of the default
controller.

unit-number represents the unit number of the SCSI
or Ethernet device from which you are booting the
operating system.

partition-number represents the number (or other
designator) of the partition from which you are booting
the operating system. When booting from a tape, this
number is not used because the boot file must be the
first thing on the tape. When booting from a disk, this
number depends on how you partitioned the disk when
you installed your operating system software. Refer to
the software installation manual if you need a reminder
about disk partition indicators.

file name represents the name of the operating system
file.

Console Commands Generated by Version PDE3 ROM Chips

E–27

Содержание DECstation 5000 Model 100 Series














































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды