manualshive.com logo in svg

DEC DECstation 5000 Model 100 Series, Руководство по обслуживанию

Поделиться
Скачать
DEC DECstation 5000 Model 100 Series Скачать руководство пользователя страница 234

Ethernet Tests

The following entries explain the purpose, test commands, and
error messages for each individual Ethernet test.

Registers Test

The registers test performs a read/write operation on the
Ethernet register. To run the registers test, type t x01, where x
represents the unit number of the Ethernet controller you want
to test, and press Return.

Registers test parameters and error codes

In registers test error messages, P1 indicates the last value
that was read from CSR0.

Table F-34 lists the error codes used in registers test error
messages.

Table F-34.

Registers Test Error Codes

Error Code

Description

1

First write to Ethernet CSRs failed.

2

Reading CSR values and comparing them to zero failed.

3

Comparing value in CSR1 to pattern of all ones failed.

4

Comparing value in CSR2 to pattern of all ones failed.

5

Test for bit leak from CSR2 to CSR1 failed.

6

Test for bit leak from CSR1 to CSR2 failed.

7

Immediate write/read test failed.

F–28

Test Commands and Messages Produced by Version PDE3 ROM Chips

Содержание DECstation 5000 Model 100 Series














































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды