manualshive.com logo in svg

DEC DECstation 5000 Model 100 Series, Руководство по обслуживанию

Поделиться
Скачать
DEC DECstation 5000 Model 100 Series Скачать руководство пользователя страница 192

Table E-3 (Cont.).

Environment Variables Set by the User

Environment
Variable

Description

console

One or more devices to use as the console terminal.
If more than one device is designated as a console,
the system accepts input from and sends output to all
designated devices. The following are allowable values:

tty(0), which enables the system’s regular console

tty(2), which enables a terminal attached to the
right communications line connector

tty(3), which enables a terminal attached to the
left communications line connector

The regular console is the system’s default console,
if available. If this console is not available, the
next default is a console attached to the right
communications line connector.

Kbd

Keyboard language. Specify the number that
corresponds to the keyboard language you want to use.
To display available languages and numbers, set Kbd
to 0 and turn off the system unit. The list of keyboard
languages appears on the monitor.

scsiid0

Address given to the controller on the system’s first
SCSI bus. Default is 6.

scsiid1

Address given to the controller on the system’s second
SCSI bus. Default is 6.

scsiid2

Address given to the controller on the system’s third
SCSI bus. Default is 6.

scsiid3

Address given to the controller on the system’s fourth
SCSI bus. Default is 6.

E–14

Console Commands Generated by Version PDE3 ROM Chips

Содержание DECstation 5000 Model 100 Series














































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды