Danfoss VLT FCD 303 Скачать руководство пользователя страница 92

Страница: 92 / 127

VLT

FCD Series

Description of choice:

Jog frequency f

JOG

can be selected between

0 Hz and f

MAX

512 Telegram Profile

(TELEGRAM PROFILE)

Value:

Profidrive (PROFIDRIVE)

[0]

✭

FC protocol (FC PROTOCOL)

[1]

Fast I/O FC-profile (FAST I/O FC-PROFILE)

[2]

Function:

It is possible to choose between three different

control word profiles.

Description of choice:

Select the desired control word profile.

See

Serial port for FCD 300

for further details

of control word profiles.

513 Bus time interval

(BUS TIMEOUT TIME)

Value:

1 - 99 sec.

✭

1 sec.

Function:

In this parameter it is possible to preset the maximum

time expected to elapse between receipt of two

consecutive telegrams. If this time is exceeded, the

serial communication is assumed to have stopped

and the desired reaction is preset in parameter

514

Bus time interval function

Description of choice:

Preset the required time.

514 Bus time interval function

(BUS TIMEOUT FUNC)

Value:

✭

Off (OFF)

[0]

Freeze output frequency (FREEZE OUTPUT)

[1]

Stop (STOP)

[2]

Jogging (JOGGING)

[3]

Max. speed (MAX SPEED)

[4]

Stop and trip (STOP AND TRIP)

[5]

Function:

In this parameter you can select the required

reaction for the frequency converter when the

preset time in parameter 513

Bus time interval

has

been exceeded. If choices [1] to [5] are activated

the output relay will be deactivated.

Description of choice:

The output frequency of the frequency converter

can be frozen at the present value, stop the motor,

be frozen at parameter 213

Jogging frequency

, be

frozen at parameter 202

Output frequency, high

limit f

MAX

or stop and activate a cut out.

✭

= factory setting. () = display text [] = value for use in communication via serial communication port

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды