Danfoss VLT FCD 303 Скачать руководство пользователя

Страница: 41 / 127

VLT

FCD Series

Programming, FCD

300

NB!:

The max. value equals f

M,N

x 60. f

M,N

to be

set in parameter 104

Motor frequency, f

M,N

107 Automatic motor tuning, AMT

(AUTO MOTOR TUN.)

Value:

✭

Optimisation off (AMT OFF)

[0]

Optimisation on (AMT START)

[2]

Function:

Automatic motor tuning is an algorithm that measures

stator resistance R

without the motor axle turning.

This means that the motor is not delivering any torque.

AMT can be used with benefit when initialising units

where the user wishes to optimise adjustment of

the frequency converter to the motor being used.

This is used in particular when the factory setting

does not sufficiently cover the motor.

For the best possible tuning of the frequency converter

it is recommended that AMT is performed on a

cold motor. It should be noted that repeated AMT

runs can cause heating of the motor, resulting

in an increase in the stator resistance R

. As a

rule, however, this is not critical.

AMT is performed as follows:

Start AMT:

1. Give a STOP signal.

2. Parameter 107

Automatic motor tuning

is set

at value [2]

Optimisation on

3. A START signal is given and parameter 107

Automatic motor tuning

is reset to [0] when

AMT has been completed.

In factory setting START requires terminals 18 and

27 to be connected to terminal 12.

Complete AMT:

AMT is completed by giving a RESET signal.

Parameter 108

Stator resistance, Rs

is updated

with the optimised value.

Interrupting AMT:

AMT can be interrupted during the optimisation

procedure by giving a STOP signal.

When using the AMT function the following

points should be observed:

For AMT to be able to define the motor parameters

as well as possible, the correct type plate data for

the motor connected to the frequency converter

must be keyed into parameters 102 to 106.

Alarms will appear in the display if faults arise

during tuning of the motor.

As a rule the AMT function will be able to measure

the R

values for motors that are 1-2 times larger or

smaller than the frequency converter

’

s nominal size.

If you wish to interrupt automatic motor tuning,

press the [STOP/RESET] key.

NB!:

AMT may not be performed on motors

connected in parallel, nor may setup changes

be made while AMT is running.

Description of choice:

Select

Optimisation on

[2] if you want the frequency

converter to perform automatic motor tuning.

108 Stator resistance R

(STATOR RESISTAN)

Value:

0.000 - X.XXX

✭

Depends on choice of motor

Function:

After setting of parameters 102-106

Nameplate data,

a number of adjustments of various parameters is

carried out automatically, including stator resistance

. A manually entered R

must apply to a cold

motor. The shaft performance can be improved by

fine-tuning R

and X

, see procedure below.

NB!:

Parameters 108

Stator resistance R

and 109

Stator reactance X

are normally not to be

changed if nameplate data has been set.

Description of choice:

can be set as follows:

1. Use the factory settings of R

which the

frequency converter itself chooses on the basis

of the motor nameplate data.

2. The value is stated by the motor supplier.

3. The value is obtained through manual

measurements: R

can be calculated by measuring

the resistance R

PHASE-PHASE

between two phase

terminals.

= 0.5 x R

PHASE-PHASE

4. R

is set automatically when AMT has

been completed. See parameter 107

Auto motor adaption.

✭

= factory setting. () = display text [] = value for use in communication via serial communication port

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды