Danfoss VLT FCD 303 Скачать руководство пользователя страница 12

Страница: 12 / 127

VLT

FCD Series

■

ATEX correct installation

The following issues must be taken into account when

installing the FCD 300 in ATEX zone 22 environments:

•

Motor must be designed, tested and certified by the

motor manufacturer for variable speed application

•

Motor must be designed for Zone 22 operation.

I.e. with type of protection "tD" acc. to

EN61241-0 and -1 or EN50281-1-1.

•

Motor must be provided with thermistor protection.

The thermistor protection must either be connected

to an external thermistor relay, with EC Type

Examination Certificate or compatible with

the FCD 300 thermistor input.

If the FCD 300 thermistor protection is used,

the thermistor must be wired to terminals

31a and 31b, and thermistor trip activated by

programming parameter 128 to thermistor trip

[2]. See parameter 128 for further details.

•

Cable entries must be chosen for the enclosure

protection to be maintained. It must also be

ensured that the cable entries comply with the

requirements for clamping force and mechanical

strengths as described in EN 50014:2000.

•

The FCD must be installed with appropriate earth

connecting according to local/national regulations.

•

The installation, inspection and maintenance of

electrical apparatus for use in combustible dusts,

must only be carried out by personnel that is

trained and familiar with the concept of protection.

For a declaration of conformity, please consult

your local Danfoss representative.

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды