Danfoss VLT FCD 303 Скачать руководство пользователя

Страница: 104 / 127

VLT

FCD Series

ALARM 16: Short-circuit

There is a short-circuit on the motor terminals or

in the motor. Disconnect the mains supply to the

frequency converter and remove the short-circuit.

WARNING/ALARM 17: Serial commu-
nication timeout

There is no serial communication to the frequency

converter. The warning will only be active when 514

Bus timeout function

is set to a value other than OFF. If

parameter 514

Bus timeout function

is set to

Stop and

trip

[5], it will first give a warning and then ramp down

and trip out accompanied by an alarm. Parameter

513

Bus timeout

can if required be increased

WARNING/ALARM 18: HPFB bus timeout

There is no serial communication to the frequency

converter

’

s communication option card. This warning

will only be active when parameter 804

Bus timeout

function

is set to a value other than OFF. If parameter

804

Bus timeout function

is set to

Stop and trip

, it

will first give a warning and then ramp down and

trip out accompanied by an alarm. Parameter 803

Bus timeout

can if required be increased.

WARNING 33: Out of frequency range

This warning is active if the output frequency has

reached

Output frequency low limit

(parameter 201) or

Output frequency high limit

(parameter 202). If the VLT

frequency converter is in

Process regulation, closed

loop

(parameter 100) the warning will be active in the

display. If the VLT frequency converter is in another

mode than

Process regulation, closed loop

, bit 008000

Out of frequency range

in extended status word will be

active, but there will not be a warning in the display.

WARNING/ALARM 34: HPFB communication fault

Communication fault only occurs in Profibus versions.

ALARM 35: Inrush fault

This alarm occurs when the frequency converter

has been connected to the mains supply too

many times within 1 minute.

WARNING/ALARM 36: Overtemperature

If the internal temperature rises above 75 - 85 °C

(depending on the device) the frequency converter

will emit a warning, and the motor will continue to

run unchanged. If the temperature continues to rise,

the switch frequency is reduced automatically. See

Temperature-dependent switching frequency

If the internal temperature of the heatsink rises above

92 - 100 °C (depending on the unit) the frequency

converter will cut out. The temperature fault cannot

be reset until the temperature of the internal heatsink

has dropped to below 70 °C. The tolerance is ± 5 °C.

The temperature can be caused by the following:

The ambient temperature too high.

Motor cable too long.

Too high mains voltage.

ALARM 37–45: Internal fault

Internal faults 0–8 will be indicated in LED

’

s Alarm,

Warning, Bus, Status as a flashing code.

Alarm 37, internal fault number 0: Communication

fault between control card and BMC2.

Alarm 38, internal fault number 1: Flash

EEPROM fault on control card.

Alarm 39, internal fault number 2: RAM

fault on control card

Alarm 40, internal fault number 3: Calibration

constant in EEPROM.

Alarm 41, internal fault number 4: Data

values in EEPROM.

Alarm 42, internal fault number 5: Fault in

motor parameter database.

Alarm 43, internal fault number 6: General

power card fault.

Alarm 44, internal fault number 7: Minimum software

version of control card or BMC2

Alarm 45, internal fault number 8: I/O fault (digital

input/output, relay or analog input/output)

NB!:

When restarting after an alarm 38-45, the

VLT frequency converter will display an

alarm 37. In parameter 615 the actual

alarm code can be read.

ALARM 50: AMT not possible

One of the following three possibilities can occur:

The calculated R

value falls outside permitted limits.

The motor current in at least one of the

motor phases is too low.

The motor in use is probably too small for AMT

calculations to be performed.

ALARM 51: AMT Fault re. nameplate data

There is inconsistency between the registered motor

data. Check the motor data for the relevant setup.

ALARM 54: AMT incorrect motor

AMT cannot be performed on the motor being used.

ALARM 55: AMT timeout

Calculations are taking too long, possibly due

to noise on the motor cables.

MG.04.B7.02 - VLT is a registered Danfoss trademark

104

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды