Danfoss VLT FCD 303 Скачать руководство пользователя

Страница: 29 / 127

VLT

FCD Series

Programming, FCD

300

Display mode IV:

This display mode can be called up during operation

if a change has to be made in another Setup without

stopping the frequency converter. This function is

activated in parameter 005

Programming Setup

MOTOR IS RUNNING

50.0 Hz

24.3% 30.2% 13.8A

SETUP

Here the programming Setup number 2 will flash

to the right of the active Setup.

■

Parameter Setup

A frequency converter

’

s comprehensive work area can

be accessed via a large number of parameters, making

it possible to adapt its functionality for a specific

application. To provide a better overview of the many

parameters, there is a choice of two programming

modes - Menu mode and Quick Menu mode. The

former provides access to all parameters. The latter

takes the user through the parameters, which make

it possible to start operating the frequency converter

in most cases, in accordance with the Setup made.

Regardless of the mode of programming, a change

of a parameter will take effect and be visible both in

the Menu mode and in the Quick menu mode.

Structure for Quick menu mode v Menu mode

In addition to having a name, each parameter is linked

up with a number which is the same regardless of

the programming mode. In Menu mode, parameters

will be split into groups, with the first digit (left)

of the parameter number indicating the group

number of the parameter in question.

•

Using the [QUICK MENU] key, it is possible to

get access to the most important parameters

of the frequency converter. After programming,

the frequency converter is in most cases ready

for operation. Scroll through the Quick menu

using the [+ / -] keys and change the data values

by pressing [CHANGE DATA] + [OK].

•

The Menu mode allows choosing and changing

all parameters as required. However, some

parameters will be "shaded off", depending on the

choice in parameter 100

Configuration

■

Quick menu with LCP 2 control unit

Start Quick Setup by pressing the [QUICK MENU] key,

which will bring out the following display values:

50.0 Hz

SETUP

QUICK MENU X OF Y

001 LANGUAGE

ENGLISH

At the bottom of the display, the parameter number

and name are given together with the status/value

of the first parameter under the Quick menu. The

first time the [QUICK MENU] key is pressed after

the unit has been switched on, the readouts always

start in pos. 1 - see table below.

Pos.

Parameter no.

Unit

001 Language

102 Motor power

[kW]

103 Motor voltage

[V]

104 Motor frequency

[Hz]

105 Motor current

[A]

106 Rated motor speed

[rpm]

107 AMT

204 Minimum reference

[Hz]

205 Maximum reference

[Hz]

207 Ramp-up time

[sec]

208 Ramp-down time

[sec]

002 Local/remote operation

003 Local reference

[Hz]

■

Parameter selection

Menu mode is started by pressing the [MENU] key,

which produces the following readout on the display:

50.0 Hz

FREQUENCY

0 KEYB.&DISPLAY

Line 3 on the display shows the parameter

group number and name.

In Menu mode, the parameters are divided

into groups. Selection of parameter group is

effected using the [< >] keys.

The following parameter groups will be accessible:

Group no.

Parameter group

Operation & Display

Load & Motor

References & Limits

Inputs & Outputs

Special functions

Serial communication

Technical functions

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды