Danfoss VLT FCD 303 Скачать руководство пользователя

Страница: 81 / 127

VLT

FCD Series

Programming, FCD

300

Example - Write a parameter value:

Parameter 202

Output frequency high limit, f

MAX

be changed to 100 Hz. The value must be recalled

after a mains failure, so it is written in EEPROM.

PKE = E0CA Hex - Write for parameter 202

Output frequency high limit, f

MAX

IND = 0000 Hex

PWE

HIGH

= 0000 Hex

PWE

LOW

= 03E8 Hex - Data value 1000,

corresponding to 100 Hz, see conversion.

The response from the slave to the master will be:

Example - Selection of a data value:

You wish to select kg/hour [20] in parameter 416

Process units

. The value must be recalled after a

mains failure, so it is written in EEPROM.

PKE = E19F Hex - Write for parameter

416

Process units

IND = 0000 Hex

PWE

HIGH

= 0000 Hex

PWE

LOW

= 0014 Hex - Select data option

kg/hour [20]

The response from the slave to the master will be:

Example - Reading a parameter value:

The value in parameter 207

Ramp up time 1

is required.

The master sends the following request:

PKE = 10CF Hex - read parameter 207

Ramp up time 1

IND = 0000 Hex

PWE

HIGH

= 0000 Hex

PWE

LOW

= 0000 Hex

If the value in parameter 207

Ramp-up time 1

is 10

sec., the response from the slave to the master will be:

Conversion:

Under the section entitled

Factory Settings

the

various attributes of each parameter are displayed.

As a parameter value can only be transferred

as a whole number, a conversion factor must

be used to transfer decimals.

Example:

Parameter 201

Output frequency, low limit f

MIN

has

a conversion factor of 0.1. If you wish to preset the

minimum frequency to 10 Hz, the value 100 must

be transferred, as a conversion factor of 0.1 means

that the value transferred is multiplied by 0.1. The

value 100 will thus be perceived as 10.0.

Conversion table

Conversion

index

Conversion

factor

0.1

100

-1

0.1

-2

0.01

-3

0.001

-4

0.0001

-5

0.00001

■

Process Words

The block of process words is divided into two blocks

of 16 bits, which always occur in the defined sequence.

PCD 1

PCD 2

Control telegram

(master

⇒

slave)

Control word

Reference-

value

Control telegram

(slave

⇒

master)

Status word

Present outp.

frequency

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды