Danfoss VLT FCD 303 Скачать руководство пользователя страница 54

Страница: 54 / 127

VLT

FCD Series

214 Reference function

(REF FUNCTION)

Value:

✭

Sum (SUM)

[0]

Relative (RELATIVE)

[1]

External/preset (EXTERNAL/PRESET)

[2]

Function:

It is possible to define how preset references are to

be added to the other references; for this purpose,

use

Sum

Relative

. It is also possible by using the

External/preset

to select whether a shift between

external references and preset references is required.

External reference is the sum of the analogue

references, pulse references and any references

from serial communication.

Description of choice:

Sum

[0] is selected, one of the adjusted

preset references (parameters 215-218

Preset

reference

) is summarized as a percentage of

the reference range (Ref

MIN

- Ref

MAX

), added

to the other external references.

Relative

[1] is selected, one of the added

preset references (parameters 215-218

Preset

reference

) is summarized as a percentage of the

sum of present external references.

External/preset

[2] is selected, it is possible via

a digital input to shift between external references

or preset references. Preset references will be a

percentage value of the reference range.

NB!:

If Sum or Relative is selected, one of the

preset references will always be active. If the

preset references are to be without influence,

they must be set to 0% (factory setting).

215 Preset reference 1 (PRESET REF. 1)

216 Preset reference 2 (PRESET REF. 2)

217 Preset reference 3 (PRESET REF. 3)

218 Preset reference 4 (PRESET REF. 4)

Value:

-100.00% - +100.00%

✭

0.00%

of the reference range/external reference

Function:

Four different preset references can be programmed

in parameters 215-218

Preset reference

The preset reference is stated as a percentage of the

reference range (Ref

MIN

- Ref

MAX

) or as a percentage

of the other external references, depending on the

choice made in parameter 214

Reference function

The choice between preset references can be made

via the digital inputs or via serial communication.

Preset ref., msb

Preset ref. lsb

Preset ref. 1

Preset ref. 2

Preset ref. 3

Preset ref. 4

Description of choice:

Set the preset reference(s) that is/are to be the options.

219 Catch up/ Slow down reference

(CATCH UP/SLW DWN)

Value:

0.00 - 100% of the given reference

✭

0.00%

Function:

In this parameter, the percentage value can be

set which will either be added to or deducted

from the remote-controlled references.

The remote-controlled reference is the sum of preset

references, analogue references, pulse reference and

any references from serial communication.

Description of choice:

Catch up

is active via a digital input, the percentage

value in parameter 219

Catch up/Slow down reference

will be added to the remote-controlled reference.

Slow down

is active via a digital input, the percentage

value in parameter 219

Catch up/Slow down reference

will be deducted from the remote-controlled reference.

221 Current limit, I

LIM

(CURRENT LIMIT)

Value:

0 - XXX.X % of par. 105

✭

160 %

Function:

In this parameter, the maximum output current I

LIM

is set. The factory-set value corresponds to the

maximum output current I

MAX

. If the current limit

is to be used as motor protection, set the rated

motor current. If the current limit is set above 100%

(the rated output current of the frequency converter,

INV.

), the frequency converter can only handle a load

intermittently, i.e. for short periods at a time. After the

load has been higher than I

INV.

, it must be ensured that

for a period the load is lower than I

INV.

Please note that

if the current limit is set at a lower value than I

INV.

, the

acceleration torque will be reduced to the same extent.

✭

= factory setting. () = display text [] = value for use in communication via serial communication port

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды