Danfoss VLT FCD 303 Скачать руководство пользователя

Страница: 8 / 127

VLT

FCD Series

■

Mechanical installation

Please pay attention to the requirements

that apply to integration and remote

mounting. These must be complied

with to avoid serious injury or damage, especially

when installing large units.

The FCD 300 consists of two parts: The installation

part and the electronics part.

The two parts must be separated, and the installation

part is to be mounted first. After wiring, the electronics

is to be fixed to the installation part by the attached

6 screws. For compressing the gasket the screws

must be tightened with 2-2.4 Nm, tighten both centre

screws first, thereafter the 4 corner srews "cross over".

NB!:

Do not switch on the mains before the

6 screws are tightened.

The FCD 300 can be applied as following:

Stand alone mounted close to the motor

Motor mounted

or might be delivered pre mounted on a Danfoss

Bauer (geared) motor. Please contact the Danfoss

Bauer sales organisation for further information.

The frequency converter is cooled by means of air

circulation. For the unit to be able to release its

cooling air, the minimum free distance above and

below the unit must be minimum 100 mm. To protect

the unit from overheating, it must be ensured that the

ambient temperature does not rise above the max.

temperature stated for the frequency converter and

that the 24-hour average temperature is not exceeded.

The max. temperature and 24-hour average can

be seen in

General technical data

. If the ambient

temperature is higher, derating of the frequency

converter is to be carried out. See

Derating for

ambient temperature

. Please note that the service life

of the frequency converter will be reduced if derating

for ambient temperature is not considered.

Stand alone mounting ("wall mounting")

For best cooling the unit should be mounted vertically,

however where space limitations require it, horizontal

mounting is allowable. The integrated 3 wall mounting

brackets in the wall mounting version can be used

for fixing the installation box to the mounting surface,

keeping a distance for possible cleaning between

the box and the mounting surface. Use the three

supplied washers to protect the paint.

Bolts must be M6 for the FCD 303 - 315

and M8 for FCD 322 - 335.

See Dimensional Drawings.

Motor mounting

The installation box should be mounted on the

surface of the motor frame, typically instead of the

motor terminal box. The motor/geared motor may

be mounted with the shaft vertically or horizontally.

The unit mustnot be mounted upside down (the heat

sink pointing down). The cooling of the electronics is

independent on the motor cooling fan. For mounting

directly on Danfoss Bauer geared motors no adaption

plate is necessary. For motor mounting (non Danfoss

Bauer motors), an adaptor plate should usually be

applied. For that purpose a neutral plate incl gasket

and screws for attaching to the installation box is

available. The appropriate drillings and gasket for the

motor housing are applied locally. Please make sure,

that the mechanical strength of the mounting screws

and the threads are sufficient for the application. The

specified resistance against mechanical vibrations

does not cover the mounting onto a non Danfoss

Bauer motor, as the stability of the motor frame

and threads are outside Danfoss Drive

’

s control and

responsibility and the same applies to the enclosure

class. Please be aware, that the frequency converter

may not be used to lift the motor/geared motor.

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды