Danfoss VLT FCD 303 Скачать руководство пользователя

Страница: 38 / 127

VLT

FCD Series

025 Quick Menu setup

(QUICK MENU SETUP)

Value:

[Index 1 - 20] Value: 0 - 999

✭

000

Function:

In this parameter you define which parameters are

required in the Quick Menu when parameter 024

User-defined Quick Menu

is set to

Active

[1]

Up to 20 parameters can be selected for the

user-defined Quick Menu.

NB!:

Please note that this parameter can only be set

using an LCP 2 control panel. See

Order form

Description of choice:

The Quick Menu is set up as follows:

1. Select parameter 025

Quick Menu setup

and press [CHANGE DATA].

2. Index 1 indicates the first parameter in Quick

Menu. You can scroll between the index numbers

using the [+ / -] keys. Select Index 1.

3. Using [< >] you can scroll between the

three figures. Press the [<] key once ad

the last number in the parameter number

can be selected using the [+ / -] keys.

Set Index 1 to 100 for parameter 100

Configuration

4. Press [OK] when Index 1 has been set to 100.

5. Repeat steps 2 - 4 until all parameters required

have been set to the Quick Menu key.

6. Press [OK] to complete the Quick Menu setup.

If parameter 100

Configuration

is selected at

Index 1, Quick Menu will start with this parameter

every time Quick Menu is activated.

Please note that parameter 024

User-defined Quick

Menu

and parameter 025

Quick Menu setup

are

reset to the factory setting during initialisation.

026

LED Status

(LED STATUS)

Value:

✭

Overload (OVERLOAD)

[0]

Therm. warn/alarm 36 (OVERTEMP)

[1]

Thermistor/ETR (THERMAL MOTOR)

[2]

Digital input 18 (DIGITAL INPUT 18)

[3]

Digital input 19 (DIGITAL INPUT 19)

[4]

Digital input 27 (DIGITAL INPUT 27)

[5]

Digital input 29 (DIGITAL INPUT 29)

[6]

Digital input 33 (DIGITAL INPUT 33)

[7]

As relay par. 323 (AS RELAY / P323)

[8]

As dig.outp. par. 341 (AD DIG. OUT. / P341)

[9]

As mech.brake output

(AS MECH. BRAKE OUTPUT)

[10]

Function:

This parameter enables the user to visualize different

situations using the Status LED.

Description of choice:

Select the function to be visualized.

✭

= factory setting. () = display text [] = value for use in communication via serial communication port

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды