Danfoss VLT FCD 303 Скачать руководство пользователя

Страница: 73 / 127

VLT

FCD Series

Programming, FCD

300

427 U3 voltage

(U3 VOLTAGE)

Value:

0.0 - 999.0 V

✭

par.

103

Function:

See parameter 423

U1 voltage

Description of choice:

Set the output voltage (U3) that is to match the third

output frequency (F3), parameter 428

F3 frequency

428 F3 frequency

(F3 FREQUENCY)

Value:

Par.

426

F2 frequency

- 1000 Hz

✭

Par. 104

Motor frequency

Function:

See parameter 423

U1 voltage

Description of choice:

Set the output frequency (F3) that is to match the third

output voltage (U3), parameter 427

U3 voltage

NB!:

Parameters 437-444 are only used

if in parameter 100

Configuration

selection has been made of

Process

regulation, closed loop.

[3].

437 Process PID normal/inverse control

(PROC NO/INV CTRL)

Value:

✭

Normal (NORMAL)

[0]

Inverse (INVERSE)

[1]

Function:

It is possible to choose whether the process regulator

is to increase/reduce the output frequency if there

is a deviation between the reference/setpoint

and the actual process mode.

Description of choice:

If the frequency converter is to reduce

the output frequency in case the feed-

back signal increases, select

Normal

[0].

If the frequency converter is to increase the

output frequency in case the feedback signal

increases, select

Inverse

[1].

438 Proces PID anti windup

(PROC ANTI WINDUP)

Value:

Not active (DISABLE)

[0]

✭

Active (ENABLE)

[1]

Function:

It is possible to select whether the process regulator is

to continue regulating on a deviation even if it is not

possible to increase/reduce the output frequency.

Description of choice:

The factory setting is

Enable

[1], which means that

the integration link is initialised in relation to the

actual output frequency if either the current limit, the

voltage limit or the max./min. frequency has been

reached. The process regulator will not engage

again until either the error is zero or its sign has

changed. Select

Disable

[0] if the integrator is to

continue integrating on the deviation, even if it is not

possible to remove the fault by such control.

NB!:

Disable

[0] is selected, it will mean that when

the deviation changes its sign, the integrator

will first have to integrate down from the

level obtained as a result of the former error, before

any change in output frequency occurs.

439 Process PID start frequency

(PROC START VALUE)

Value:

MIN

- f

MAX

(parameter 201/202)

✭

Par. 201

Output frequency, low limit, f

MIN

Function:

When the start signal comes, the frequency converter

will react in the form of

Open loop

and will not

change to

Closed loop

until the programmed start

frequency is reached. This makes it possible to set a

frequency that corresponds to the speed at which the

process normally runs, which will enable the required

process conditions to be reached sooner.

Description of choice:

Set the required start frequency.

✭

= factory setting. () = display text [] = value for use in communication via serial communication port

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды