Danfoss VLT FCD 303 Скачать руководство пользователя страница 102

Страница: 102 / 127

VLT

FCD Series

■

Warnings/alarm messages

A warning or an alarm will appear in the LEDs on

the LCP2. A warning will be shown until the fault

has been corrected, while an alarm will continue

to flash until the [STOP/RESET] key is activated.

The table shows the various warnings and alarms

shown in the LCP2, and whether the fault locks the

frequency converter. After a

Trip locked

(alarm and

warning LEDs flash at the same time), the mains

supply is cut off and the fault is corrected. The mains

supply is reconnected and the frequency converter

is reset. The frequency converter is now ready. A

Trip

can be reset manually in three ways:

1. Via the operating key [STOP/RESET].

2. Via a digital input.

3. Via serial communication.

It is also possible to choose an automatic reset in

parameter 405

Reset function

. When a cross appears

in both warning and alarm, this can mean that a

warning comes before an alarm. It can also mean

that it is possible for the user to programme whether

a warning or an alarm will appear for a given fault.

For example, this is possible in parameter 128

Motor

thermal protection

. After a trip the motor will coast,

and alarm and warning will blink on the frequency

converter, but if the fault disappears only the alarm

will blink. After a reset the frequency converter

will be ready to start operation again.

No.

Description

Warning

Alarm

Trip

locked

Live zero error (LIVE ZERO ERROR)

Mains phase loss (MAINS PHASE LOSS)

Voltage warning high (DC LINK VOLTAGE HIGH)

Voltage warning low (DC LINK VOLTAGE LOW)

Overvoltage (DC LINK OVERVOLT)

Undervoltage (DC LINK UNDERVOLT)

Inverter overload (INVERTER TIME)

Motor overloaded ( MOTOR, TIME)

Motor thermistor (MOTOR THERMISTOR)

Current limit (CURRENT LIMIT)

Overcurrent (OVERCURRENT)

Earth fault (EARTH FAULT)

Switch mode fault (SWITCH MODE FAULT)

Short-circuit (CURR. SHORT CIRCUIT)

Serial communication timeout (STD BUS TIMEOUT)

HPFB bus timeout (HPFB TIMEOUT)

Out of frequency range (OUT FREQ RNG/ROT LIM)

HPFB communication fault (PROFIBUS OPT. FAULT)

Inrush fault (INRUSH FAULT)

Overtemperature (OVERTEMPERATURE)

37-45

Internal fault (INTERNAL FAULT)

AMT not possible

AMT fault re. nameplate data (AMT TYPE.DATA FAULT)

AMT wrong motor (AMT WRONG MOTOR)

AMT timeout (AMT TIMEOUT)

AMT warning during AMT (AMT WARN. DURING AMT)

Locked (LOCKED)

LED indication

Warning

yellow

Alarm

red

Trip locked

yellow and red

WARNING/ALARM 2: Live zero fault

The voltage or current signal on terminal 53 or

60 is below 50% of the preset value in parameter

309 or 315

Terminal, min. scaling

WARNING/ALARM 4: Mains phase fault

No phase on mains supply side. Check the supply

voltage to the frequency converter. This fault is only

active in 3-phase mains supply. The alarm can only

occur when the load is pulsing. In this instance the

pulses must be dampened, e.g. using an inertia disc.

MG.04.B7.02 - VLT is a registered Danfoss trademark

102

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды