Danfoss VLT FCD 303 Скачать руководство пользователя страница 26

Страница: 26 / 127

VLT

FCD Series

■

The LCP 2 control unit, option

The FCD 300 can be combined with an LCP control

unit (Local Control Panel - LCP 2) which makes up a

complete interface for operation and programming of

the frequency converter. The LCP 2 control unit can

be attached up to three metres from the frequency

converter, e.g. on a front panel, using an accessory kit.

The control panel is divided into five functional groups:

1. Display.

2. Keys used to change the display function.

3. Keys used to change the programme parameters.

4. Indicator lamps.

5. Local control keys.

All data is displayed via a 4-line alphanumeric

display, which during normal operation will be able

to continuously display 4 items of operating data

and 3 operating modes. During programming all

information needed for quick, effective parameter

setup of the frequency converter will be displayed. As

a supplement to the display, there are three indicator

lamps for voltage (ON), warning (WARNING) and alarm

(ALARM). All frequency converter parameter Setups

can be changed immediately from the control panel,

unless this function has been programmed as

Locked

[1] via parameter 018

Lock for data changes

■

Control keys for parameter Setup

The control keys are divided into functions, in

such a way that the keys between the display

and the indicator lamps are used for parameter

Setup, including selection of the display

’

s view

mode during normal operation.

[DISPLAY/STATUS]

is used to select the display

’

view mode or to change back to Display mode

from either Quick Menu or Menu mode.

[QUICK MENU]

provides access to the parameters

used in the Quick Menu. It is possible to switch

between Quick Menu and Menu mode.

[MENU]

gives access to all parameters. It is possible

to switch between Menu mode and Quick Menu.

[CHANGE DATA]

is used to change a parameter that

has been selected either in Menu mode or Quick Menu.

[CANCEL]

is used if a change to the selected

parameter is not to be implemented.

[OK]

is used to confirm a change to a

selected parameter.

[+ / -]

are used for selecting parameters and

for changing parameter values.

These keys are also used in Display mode to switch

between the readouts of operating variables.

[< >]

are used for selecting parameter group and to

move the cursor when changing a numerical value.

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды