Danfoss VLT FCD 303 Скачать руководство пользователя

Страница: 27 / 127

VLT

FCD Series

Programming, FCD

300

■

Indicator lamps

At the bottom of the control panel are a red

alarm lamp, a yellow warning lamp and a

green voltage indicator lamp.

If certain threshold values are exceeded, the alarm

and/or warning lamp are activated, while a status

or alarm text is shown on the display.

NB!:

The voltage indicator lamp is activated when

voltage is connected to the frequency converter.

■

Local control

[STOP/RESET]

is used for stopping the motor

connected or for resetting the frequency converter

after a drop-out (trip). Can be set to active or

inactive via parameter 014

Local stop

If stop is activated Display line 2 will flash.

NB!:

If an external stop function is not selected and

the [STOP/RESET] key is set to inactive, the

motor can only be stopped by disconnecting

the voltage to the motor or the frequency converter.

[JOG]

changes the output frequency to a preset

frequency while the key is held down. Can be set to

active or inactive via parameter 015

Local jog

[FWD / REV]

changes the direction of rotation of

the motor, which is indicated by means of the arrow

on the display. Can be set to active or inactive via

parameter 016

Local reversing

. The [FWD/REV] key

is only active when parameter 002

Local/remote

operation

is set to

Local control

[START]

is used to start the frequency converter. Is

always active, but cannot override a stop command.

NB!:

If the local control keys are set to inactive,

these will both become active when the

frequency converter is set to

Local control

and

Remote control

via parameter 002

Local/remote

operation

, with the exception of [FWD/REV], which

is only active in Local control.

■

Display mode

195NA113.10

VAR 2

SETUP

STATUS

VAR 1.1 VAR 1.2 VAR 1.3

In normal operation, up to 4 different display data

items can optionally be shown continuously: 1,1,

1,2, 1,3 and 2. The present operation status or

alarms and warnings that have been generated are

displayed in line 2 in the form of a number.

In the event of alarms this is displayed in lines

3 and 4 with explanatory text.

A warning will appear flashing in line 2 with

explanatory text in line 1. The active Setup

will also appear on the display.

The arrow indicates the selected direction of rotation.

Here the frequency converter shows that it has

an active reversing signal. The body of the arrow

will disappear if a stop command is given, or if the

output frequency drops below 0.1 Hz.

The bottom line displays the frequency transformer

’

status. The scrollbar shows which operating values

can be displayed in lines 1 and 2 in Display mode.

Changes are made using the [+ / -] keys.

Switching between AUTO and HAND modes

By activating the [CHANGE DATA] key in [DISPLAY

MODE] the display will indicate the mode of

the frequency converter.

Switch mode by using [+/-] key [HAND...AUTO]

In [HAND] mode the reference can be changed

by [+] or [-] keys.

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды