Danfoss VLT FCD 303 Скачать руководство пользователя

Страница: 60 / 127

VLT

FCD Series

All encoder settings are used in connection with dual

track encoders with direction recognition.

A track connected to terminal 29.

B track connected to terminal 33.

308 Terminal 53, analogue input voltage

(AI [V]53FUNCT.)

Value:

No function (NO OPERATION)

[0]

✭

Reference (REFERENCE)

[1]

Feedback (FEEDBACK)

[2]

Wobble (WOBB.DELTA FREQ [%])

[10]

Function:

In this parameter it is possible to select the function

required to be connected to terminal 53. Scaling of the

input signal is made in parameter 309

Terminal 53, min.

scaling

and parameter 310

Terminal 53, max. scaling

Description of choice:

No function

[0]. Is selected if the frequency converter

is not to react to signals connected to the terminal.

Reference

[1]. If this function is selected, the reference

can be changed by means of an analogue reference

signal. If reference signals are connected to more than

one input, these reference signals must be added up.

If a voltage feedback signal is connected, select

Feedback

[2] on terminal 53.

Wobble

[10]

The delta frequency can be controlled by the analog

input. If

WOBB.DELTA FREQ

is selected as analog

input (par. 308 or par. 314) the value selected in

par. 702 equals 100 % analog input.

Example: Analog input = 4-20 mA, Delta freq. par.

702 = 5 Hz

→

4 mA = 0 Hz and 20 mA = 5 Hz.

If this function is chosen, see Wobble Instruction

MI28JXYY for further information.

309

Terminal 53 Min. scaling

(AI 53 SCALE LOW)

Value:

0.0 - 10.0 Volt

✭

0.0 Volt

Function:

This parameter is used for setting the signal value

that is to correspond to the minimum reference or

the minimum feedback, parameter 204

Minimum

reference, Ref

MIN

/ 414

Minimum feedback, FB

MIN

Description of choice:

Set the required voltage value. For reasons of

accuracy, compensation should be made for voltage

loss in long signal cables. If the Time out function is to

be used (parameter 317

Time out

and 318

Function

after time out

), the value set must be higher than 1 Volt.

310

Terminal 53 Max. scaling

(AI 53 SCALE HIGH)

Value:

0 - 10.0 Volt

✭

10.0 Volt

Function:

This parameter is used for setting the signal value that

is to correspond to the maximum reference value

or maximum feedback, parameter 205

Maximum

reference, Ref

MAX

/ 414

Maximum feedback, FB

MAX

Description of choice:

Set the required voltage value. For reasons of

accuracy, compensation should be made for

voltage losses in long signal cables.

314 Terminal 60, analogue input current

(AI [MA] 60 FUNCT)

Value:

No function (NO OPERATION)

[0]

Reference (REFERENCE)

[1]

✭

Feedback (FEEDBACK)

[2]

Wobble (WOBB.DELTA FREQ [%])

[10]

Function:

This parameter allows a choice between the different

functions available for the input, terminal 60.

Scaling of the input signal is effected in parameter

315

Terminal 60, min. scaling

and parameter

316

Terminal 60, max. scaling

Description of choice:

No function

[0]. Is selected if the frequency converter

is not to react to signals connected to the terminal.

Reference

[1]. If this function is selected, the reference

can be changed by means of an analogue reference

signal. If reference signals are connected to more than

one input, these reference signals must be added up.

If one current feedback signal is connected,

select

Feedback

[2] on terminal 60.

Wobble

[10]

✭

= factory setting. () = display text [] = value for use in communication via serial communication port

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды