Danfoss VLT FCD 303 Скачать руководство пользователя страница 4

Страница: 4 / 127

VLT

FCD Series

■

High voltage warning

The voltage of the frequency converter

is dangerous whenever the converter

is connected to mains. Incorrect fitting

of the motor or frequency converter may cause

damage to the equipment, serious injury or death.

Consequently, it is essential to comply with the

instructions in this manual as well as local and

national rules and safety regulations.

■

These rules concern your safety

1. The frequency converter must be disconnected from

the mains if repair work is to be carried out. Check

that the mains supply has been disconnected

and that the prescribed time has passed before

removing the inverter part from the installation.

2. The [STOP/RESET] key on the optional control

panel does not disconnect the equipment from

mains and is thus not to be used as a safety switch.

3. The unit must be properly connected to the

earth, the user must be protected against the

supply voltage and the motor must be protected

against overloading pursuant to prevailing

national and local regulations.

4. The earth leakage currents are higher than 3.5 mA.

5. Protection against motor overload is not included

in the factory setting. If this function is required,

set parameter 128

Motor thermal protection

data value

ETR trip

or data value

ETR warning

. For

the North American market: The ETR functions

provide overload protection of the motor, class

20, in accordance with NEC.

■

Warning against unintended start

1. The motor can be brought to a stop by

means of digital commands, bus commands,

references or a local stop, while the frequency

converter is connected to mains. If personal

safety considerations make it necessary to

ensure that no unintended start occurs, these

stop functions are not sufficient.

2. While parameters are being changed, the

motor may start. Consequently, the stop

key [STOP/RESET] on the optional control

panel must always be activated, following

which data can be modified.

3. A motor that has been stopped may start if faults

occur in the electronics of the frequency converter,

or if a temporary overload or a fault in the supply

mains or the motor connection ceases.

195NA194.10

Warning:

It can be extremely dangerous to touch the electrical parts
even when the AC line supply has been disconnected.

For FCD 300: wait at least 4 minutes.

MG.04.B7.02 - VLT is a registered Danfoss trademark

Содержание VLT FCD 303
































































































































Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды

Danfoss VLT FCD 303, Руководство по эксплуатации

Результаты поиска

Содержание VLT FCD 303

Отзывы:

Похожие инструкции для VLT FCD 303

Бренды по названию

Популярные бренды