CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 98

Страница: 98 / 132

CTC EcoZenith i360

Menu: "Installer/Settings/Passive Cooling".

12.10.8 Settings Cooling*

Room temp. passive cooling °C

25.0 (10 or 18...30)

This is used to set the desired room temperature for

cooling.

SmartGrid Low price °C

1 (Off, 1...5)

These menu bars are displayed if room sensors are

defined in the "Installer/Define/Passive Cooling" menu.

Read more in the "Remote Control /SmartGrid" section

of the "Installer/Define" chapter.

SmartGrid Overcapacity °C

2 (Off, 1...5)

These menu bars are displayed if room sensors are

defined in the "Installer/Define/Passive Cooling" menu.

Read more in the "Remote Control /SmartGrid" section

of the "Installer/Define" chapter.

Ext. block passive cooling

Yes (Yes/No)

Blocking passive cooling can be remote controlled

remotely. For example, the function can be used to turn

off cooling with the help of a humidity sensor when there

is a risk of condensation.

This menu bar is displayed if the criteria below are met:

• a remote control input has been defined for the

"Block Passive Cooling" function.

• a normal mode (Normally Open (NO) or Normally

Closed (NC)) for the external control signal has
been defined.

Read more in the "Def. Remote Control" section of the

"Installer / Define" chapter.

Block passive cooling schedule

This menu is used to schedule the weekday periods

during which passive cooling should be blocked. This

schedule is repeated every week.

This menu bar is displayed if a weekly program has

been defined for the "Block Passive Cooling" function.

For more information, refer to:

• chapter "Weekly Program" for schedule setting.

• section "Def. Remote Control" of the

"Installer / Define" chapter for defining the remote
control function.

Содержание EcoZenith i350 L 1x230V





































































































































Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды

CTC Union EcoZenith i350 L 1x230V, Руководство по установке и обслуживанию

Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды