CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 76

Страница: 76 / 132

CTC EcoZenith i360

Heat pump status

Heat pump charging the tank.

Start delay: 1 min.

Compressor off - prevented from starting due to 1 min. start delay.

Off

Heat pump not charging the tank - no need.

Blocked in menu

Compressor Blocked in the "Installer/Settings/ Heat Pump" menu.

Communication error HP

Control unit not communicating with heat pump.

Off, start ready

Compressor off but ready to start.

Driver block under voltage

Driver operating voltage too low.

Defrost

Defrosting in progress – air-to-water heat pump only.

Stop, low outdoor temp

Outdoor temperature lower than minimum limit – air-to-water heat pump only.

Off, alarm

Compressor off – alarm activated.

Stop, tariff

Compressor blocked due to active remote control function.

Blocked, low brine in °C

Incoming brine temperature too low, compressor blocked.

Flow on

Flow in the charging coil.

12.8.3

Operation data, Heat pump
air-to-water

Status On

Heat pump status, see table below.

Model

EcoAir M

Shows the heat pump model.

Compressor

65rps R

Shows the compressor speed. "R" stands for "Reduced

Mode" (for example, during "Silent Mode").

Charge pump

On 78%

Shows operating status of the charge pump ("On" or

"Off") and the flow in percent (0-100).

Fan

On 80%

Shows operating status of the fan ("On" or "Off") and the

fan speed in percent.

HP in/out °C

35.5 /42.3

Shows the heat pump’s incoming and outgoing

temperatures.

Outdoor temp. °C

3.0 (-50...50)

Shows outdoor temperature.

Defrost timer

Shows the time remaining until the heat pump enters

defrosting mode. For the defrosting to start, the

temperature in the heat pump’s evaporator must be low

enough.

Current A

9.8

Shows the current across the compressor.

Software HP PCB

20200601

Shows the heat pump software version.

Menu: "Operation data, Heat pump".

Содержание EcoZenith i350 L 1x230V





































































































































Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды

CTC Union EcoZenith i350 L 1x230V, Руководство по установке и обслуживанию

Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды