CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 84

Страница: 84 / 132

CTC EcoZenith i360

Heat mode, schedule

This menu bar is displayed if a weekly program has

been defined for the "HC Heat Mode, ext." function in

the remote control menu.

For more information, refer to:

• chapter "Weekly Program" for schedule setting.

• section "Def. Remote Control" in chapter

"Installer / Define" chapter for defining the remote
control function.

Heating off, out °C

18 (2...30)

Heating off, time (min)

120 (30...240)

The menu bars can only be set if the "Auto" mode is

selected in the "Heat Mode" menu above. Otherwise,

the menu bars are locked (greyed out).

When the outdoor temperature exceeds (or equals) the

set value in the "Heating off, outdoor °C" menu during

the time (in minutes) set in the "Heating off, time" menu,

the production of heat for the house is stopped.

This means the radiator pump stops, and the mixing

valve remains closed. The radiator pump is activated

daily for a short period to prevent it from jamming. The

system restarts automatically when heating is needed.

When the outdoor temperature drops to the limit where

heating is needed again, heat to the house is permitted

when the temperature falls below (or equals) the set

value in the "Heating off, outdoor °C" menu for the

number of minutes set in the "Heating off, time" menu.

Inclination °C

50 (25...85)

Inclination means the temperature your property needs

at different outdoor temperatures. More information

about this can be found in the "Your home’s heating

settings" chapter.

The value set in this menu is the outgoing flow

temperature to radiators when the outdoor temperature

is -15 °C.

Adjustment °C

0 (-20...20)

The adjustment means that the temperature level can

be raised or lowered at a specific outdoor temperature.

Night reduction down to °C

5 (-40...40)

When the outdoor temperature is lower than this, the

"Night Reduction" function stops since too much energy

is consumed and it takes too long to increase the

temperature again.

This menu overrides remote control of "Night

Reduction".

Menu: "Installer/Settings/Heating Circuit/Heating Circuit 1".

Tip: Read more about these settings
in the "Your home’s heating settings"
chapter.

Example

"Inclination 50" means that the temperature of the water

supplied to the radiators will be 50°C when the outdoor

temperature is -15°C, if the adjustment is set to 0. If the

adjustment is set to +5, the temperature will be 55 °C

instead. For all outdoor temperatures the inclination is

increased by 5 °C, i.e. inclination is parallel displaced by

5 °C.

Содержание EcoZenith i350 L 1x230V





































































































































Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды

CTC Union EcoZenith i350 L 1x230V, Руководство по установке и обслуживанию

Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды