CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 106

Страница: 106 / 132

106

CTC EcoZenith i360

Part of the menu "Installer/Settings". Setting a "Round
circulation" weekly program.

Tariff EL

(Off/ K22-K25 /Channel 1A-7B / BMS DI0-7)

This function is used to block the electric heater during

periods when the electricity rate is higher.

In the "Installer / Define/Remote Control" menu:

• specify an "Input" for the remote control function.

In the "Installer/Settings/Additional Heat" menu:

• set "remote control mode" ("Yes") in the "Tariff EL"

row.

Access function scheduling from the "Tariff EL" row.

For more information, refer to the "Additional Heat/Tariff

EL" section in the "Installer/Settings" chapter.

Round circulation

(Off/ K22-K25 /Channel 1A-7B / BMS DI0-7)

Round circulation is equipment which an electricity

supplier can fit in order to disconnect, for a short period

of time, equipment which draws high current. The

compressor and electrical output are blocked when

Round circulation is active.

In the "Installer / Define/Remote Control" menu:

• specify an "Input" for the remote control function.

In the "Installer/Settings" menu:

• Access function scheduling from the "Round

circulation" row.

For more information, refer to the "Round circulation"

section in the "Installer/Settings" chapter.

Flow/level switch

(Off/ K22-K25 /Channel 1A-7B / BMS DI0-7)

The flow/level switch produces an alarm on the heat

pump.

In the "Installer / Define/Remote Control" menu:

• specify an "Input" for the remote control function.

In the "Installer / Define/Heat Pump" menu:

• configure the normal mode for the external control

signal (Normally Open (NO)/Normally Closed (NC))
in the "Flow/level switch" row.

Menu: "Installer/Define/Heat Pump".
A mode for the external control signal ("Normally Open (NO)" or
"Normally Closed (NC)").

Содержание EcoZenith i350 L 1x230V





































































































































Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды

CTC Union EcoZenith i350 L 1x230V, Руководство по установке и обслуживанию

Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды