CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 97

Страница: 97 / 132

CTC EcoZenith i360

Tariff ext. boiler

No (Yes/No)

This menu bar is displayed if an "Input" for remote

control is defined for the "Tariff EL" function in the

"Installer/Define/Remote Control" menu.

"Yes" means the function can be activated via remote

control.

Read more in the "Installer/Define/Remote Control/Tariff

EL" chapter.

Ext. boiler diff ºC

3 (Off, 1...15)

Compensation set point for External Boiler is set these

many degrees above the set point for “Primary Flow

HS1”, or “DHW,” or “Pool”. This is in addition to the

compensation made for the loss in degree minutes.

Ext. boiler schedule

This menu bar is displayed if a "Schedule" is defined for

the "Tariff EL" function in the "Installer/Define/Remote

Control" menu.

For more information, refer to:

• chapter "Weekly Program" for schedule setting.

• section "Def. Remote Control" in the "Installer /

Define" chapter for defining the remote control
function.

Содержание EcoZenith i350 L 1x230V





































































































































Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды

CTC Union EcoZenith i350 L 1x230V, Руководство по установке и обслуживанию

Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды