CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 132

background image

122

CTC EcoZenith i360

13.3 Information messages

Information messages are displayed when appropriate and are intended to

inform users about various operational situations.

[I002] HC1 Heating off

[I005] HC2 Heating off

Indicates that the product is in Summer mode. No need

for heating in the current heating system, only hot water.

[I008] Tariff HP off

Indicates that Tariff has switched off the heat pump.

[I009] Compressor blocked

The compressor is set to be shut down, e.g. before

drilling or digging has been carried out for the collector

coils. The product comes with the compressor switched

off. This option is selected in the "Installer/Settings/Heat

Pump" menu.

[I010] Tariff El off

Indicates that Tariff has switched off the electric heater.

[I011] Round circulation

Indicates that Round circulation is active. Round

circulation is a device which can be fitted by an electricity

supplier in order to disconnect equipment with a high

rate of electricity consumption for a short period of time.

Not currently in use in the UK. The compressor and

electrical output are blocked when Round circulation is

active.

[I012] High curr., reduced elec.

• The property’s main fuses risk being overloaded

due to, for example, the simultaneous use of
several power-hungry appliances. The product
reduces the electrical heaters’ electrical output
during this period.

• 2h max. 6 kW. Electric heating elements are limited

to 6 kW for 2 hours after being switched on. This
message appears if more than 6 kW are required
during the product's first 2 hours of operation.
This is applicable after a power outage or a new
installation.

[I013] Start delay

The compressor is not allowed to start too quickly after it

has stopped. The delay is usually at least 10 minutes.

[I014] Drying period active, d

Indicates that the floor function is active and displays the

time (days) remaining that the function will be active.

[I017] SmartGrid: Block

[I019] SmartGrid: Low price

[I018] SmartGrid: Overcapacity

Product functionality is governed by "SmartGrid". Also

refer to the "Installer/Define/Remote Control/SmartGrid"

menu.

[I021] Ext. Ctrl Heating 1

[I022] Ext. Ctrl Heating 2

Remote control governs whether the heat in the heating

system is to be switched on or off. If the heating is

switched off, "Heating off, heating circuit 1/2" is also

displayed.

[I028] Holiday period

Displayed when setting the holiday schedule, which

entails lowering the room temperature and that no hot

water is produced.

[I029] Bleeding DHW in progress

During the bleeding process, hot water will not be

supplied at a continuous temperature. Hot water

production can start when the bleeding process is

complete and the message is no longer displayed.

[I030] Driver block under voltage

The heat pump has stopped due to insufficient mains

voltage. The product will attempt to restart.

[I031] Driver block alarm

The heat pump has stopped due to driver failure; for

example, voltage or excessive temperature. The product

will attempt to restart.

«
...
120
121
122
123
124
...
»

Содержание EcoZenith i350 L 1x230V





































































































































Отзывы:

Нет отзывов

Похожие инструкции для EcoZenith i350 L 1x230V

Бренд: A.O. Smith Страницы: 48

Бренд: Crown Boiler Страницы: 56

CIAO GREEN R.S.I

Бренд: Beretta Страницы: 51

Бренд: Ikon Страницы: 16

Бренд: Varmebaronen Страницы: 16

KNIGHT WH 55-399

Бренд: Lochinvar Страницы: 80

Бренд: Nieco Страницы: 28

Бренд: Alpha Страницы: 52

Бренд: Beretta Страницы: 24

Бренд: HTP Страницы: 90

Бренд: Express Страницы: 4

Бренд: Potterton Страницы: 8

Modulex EXT 440

Бренд: Automatic Heating Страницы: 55

Бренд: Potterton Страницы: 32

TURBOmax VUW 242/1E

Бренд: Vaillant Страницы: 21

Бренд: Riva Страницы: 48

Ideal Esprit HE24

Бренд: Ideal Boilers Страницы: 76

Бренд: Knight Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды