CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 96

Страница: 96 / 132

CTC EcoZenith i360

12.10.7 Settings External Boiler

Ext. Boiler-Mode

Auto (Auto/On/Off)

Mode for adjusting an external boiler.

•

Auto

= adjusted as needed according to selected

settings.

•

= continuously active.

•

Off

= mode in which the external boiler does

not start, e.g., because there is no heat source
available.

Boiler start out temp.

0 (-30...30)

External boiler started at this outdoor temperature

through the powering of E1.

Delay stop ext. boiler

0 (0...1440)

If an external boiler is no longer needed, shutting it off

can be delayed. This is used to avoid operation times

too short (risk of corrosion). The boiler is kept warm for

the set time, 10 minutes at a time.

Boiler, open mix.valve ºC

70 (20...90)

This is the minimum temperature required in the external

boiler tank (B9) for the mixing valve to open and emit

heat to the system. Used to, e.g., avoid condensation in

oil boiler.

Stop diff ºC

5 (1...15)

Temperature difference compared to desired tank

temperature before the mixing valve is allowed to open.

Hysteresis for "Boiler, open mixing valve °C". When the

mixing valve has opened, the temperature may fall by

this amount before the mixing valve closes.

Start boiler, degree minute

-300 (-900...-30)

For the shunt to open and emit heat to the system, this

requires a loss of degree minutes, which is set here.

Priority DHW tank

Low (Low/High)

Controls whether the external boiler is prioritised before

electricity is added when producing hot water.

•

Low

– electric heater activated before external

boiler.

•

High

– external boiler activated before adding

electricity.

SmartGrid block boiler

No (No/Yes)

Controls whether the external boiler is blocked by

settings in SmartGrid function.

Menu “Installer/Settings/Ext Boiler”.

Содержание EcoZenith i350 L 1x230V





































































































































Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды

CTC Union EcoZenith i350 L 1x230V, Руководство по установке и обслуживанию

Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды