CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 111

Страница: 111 / 132

111

CTC EcoZenith i360

*Only applies to certain air-to-water heat pumps

12.11.3

Def. Heat pump

Heat pump

Off (On/Off)

Select whether the heat pump should be On or Off.

Flow/level switch

None (None/NC/NO)

This menu bar is displayed if an "Input" for remote

control is defined for the "Flow/level switch" function in

the "Installer/Define/Define Remote Control" menu.

Noise reduct. ext. config.

None (None/NC/NO)

This menu bar is displayed if an "Input" for remote

control is defined for the "HP Noise Reduction" function

in the "Installer/Define/Remote Control" menu.

Tariff HP config.

None (None/NC/NO)

This menu bar is displayed if an "Input" for remote

control is defined for the "HP Tariff" function in the

"Installer/Define/Remote Control" menu.

Silent mode ext. config.*

None (None/NC/NO)

This menu bar is displayed if an "Input" for remote

control is defined for the "Silent Mode" function in the

"Installer/Define/Remote Control" menu.

Menu: "Installer/Define/Heat Pump".

12.11.4

Def. Communication

MyUplink

No (Yes/No)

Select "Yes" to connect to the heat pump from the

MyUplink app.

Web

No (Yes/No)

Select "Yes" to connect to the local web server. Internet

router and firewall required.

AXS

No (Yes/No)

Select "Yes" to connect to the SmartControl wireless

communication accessory and/or WiFi.

Menu: "Installer/Define/Communication".

For more information, refer to
the "Installation Communication"
chapter of this manual.

Содержание EcoZenith i350 L 1x230V





































































































































Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды

CTC Union EcoZenith i350 L 1x230V, Руководство по установке и обслуживанию

Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды