CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 132

background image

105

CTC EcoZenith i360

On menu bar "Block. passive cooling ext. config.", the normal
mode is specified for the external control signal ("Normally
Open (NO)" or "Normally Closed (NC)").

Setting the "Extra DHW" in the "DHW" menu.

Block Passive cooling

(Off/ K22-K25 /Channel 1A-7B / BMS DI0-7)

In the "Installer / Define/Remote Control" menu:

• specify an "Input" for the remote control function.

In the "Installer / Define/Passive Cooling" menu:

• configure the normal mode for the external control

signal (Normally Open (NO)/Normally Closed (NC)).

In the "Installer/Settings/Passive Cooling" menu:

• set the "remote control mode" ("On") in the "Block.

passive cooling config." row.

Access function scheduling from the "Block. ext. config."

row.

For more information, refer to the "Passive Cooling"

section in the "Installer/Settings" chapter.

Menu: "Installer/Define/DHW" On menu bar "Extra DHW",
the normal mode is specified for the external control signal
("Normally Open (NO)" or "Normally Closed (NC)").

Extra DHW

(Off/ K22-K25 /Channel 1A-7B / BMS DI0-7)

Upon activation, production of extra DHW begins. When

activation stops, extra DHW is produced for a run-on

time of 30 min. The "Stop temperature" for extra DHW is

set in the "Installer/Settings /DHW Tank/DHW program"

menu.

In the "Installer / Define/Remote Control" menu:

• specify an "Input" for the remote control function.

In the "Installer / Define/DHW" menu:

• configure the normal mode for the external control

signal (Normally Open (NO)/Normally Closed (NC))
in the "Extra DHW" row.

Setting extra DHW production to start immediately can

also be done in the "DHW" menu. The weekly program

for extra DHW can also be set in this menu.

For more information, refer to the "Extra DHW" section

in the "DHW" chapter.

For more information, refer to the "Upper Tank" section

in the "Installer/Settings" chapter.

«
...
103
104
105
106
107
...
»

Содержание EcoZenith i350 L 1x230V





































































































































Отзывы:

Нет отзывов

Похожие инструкции для EcoZenith i350 L 1x230V

Бренд: Raypak Страницы: 76

Бренд: Toastmaster Страницы: 13

Бренд: U.S. Boiler Company Страницы: 6

WBS Active seried

Бренд: Sun System Страницы: 16

Бренд: LAMBORGHINI CALOR Страницы: 68

Wessex ModuMax mk3 WM116/116H

Бренд: Hamworthy Страницы: 68

CSI PRIMARY AAA

Бренд: Ravenheat Страницы: 4

Pellematic PE 12-20

Бренд: MAINE ENERGY SYSTEMS Страницы: 34

Бренд: Warmhaus Страницы: 40

Бренд: Eko-Vimar Orlanski Страницы: 18

Бренд: Taco Страницы: 6

BRITONY System II 100

Бренд: C&M Страницы: 12

BlueHelix ALPHA C

Бренд: ferolli Страницы: 320

Бренд: Westinghouse Страницы: 94

Бренд: ARCA Страницы: 26

Бренд: HTP Страницы: 56

Mexico Super CF4120

Бренд: Ideal Boilers Страницы: 36

Бренд: ACV Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды