CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 100

Страница: 100 / 132

100

CTC EcoZenith i360

Menu: "Installer/Settings/Current Sensors".

12.10.10 Settings Current sensor

These menu bars are displayed if "Current Sensor" is

defined in the "Installer/Define Current Sensor" menu.

In the menu, specify the phases (L1, L2 and L3) to

which the current sensors have been connected.

In the lower left corner of the screen, "Invalid

configuration" will be displayed until L1, L2, and L3 are

paired with the three current sensors in the menu.

When activating the "Auto config. current sensors"

function, it is important that you have switched off

all devices in the house that consume high levels of

electricity. Also make sure that the backup thermostat is

switched off.

Menu: "Installer/Settings/Round circulation".

12.10.11 Settings Round circulation

schedule

Round circulation is equipment which an electricity

supplier can fit in order to disconnect, for a short period

of time, equipment which draws high current. The

compressor and electrical output are blocked when

Round circulation is active.

This menu bar is displayed if a weekly program has

been defined for the "Round circulation" function.

The "Round circulation" function can also be controlled

remotely by activating the "Input" defined for the

function.

For more information, refer to:

• chapter "Weekly Program" for schedule setting.

• section "Def. Remote Control" of the

"Installer / Define" chapter for defining the remote
control function.

Menu: "Installer/Settings/Current Sensors /Auto config. current
sensor".

Содержание EcoZenith i350 L 1x230V





































































































































Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды

CTC Union EcoZenith i350 L 1x230V, Руководство по установке и обслуживанию

Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды