CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 87

Страница: 87 / 132

CTC EcoZenith i360

12.10.2 Settings Heat pump

Compressor

Blocked (Permitted/Blocked)

The heat pump is supplied with a blocked compressor.

"Permitted" means that the compressor can start.

Brine pump

Auto (Auto/10 days/On)

After installation is complete, you can choose to run the

brine pump constantly for 10 days to remove air from

the system. The brine pump then enters "Auto" mode.

"On" means the brine pump runs constantly.

Only applies to liquid-to-water heat pumps.

Stop at outdoor temp °C

-22 (-22...10)

This menu relates to settings for the outdoor

temperature at which the compressor is no longer

permitted to operate. The heat pump starts 2°C above

the set value.

Only applies to air-to-water heat pumps.

Compressor stop at brine °C

-5 (-7...10)

This menu defines the brine temperature at which the

compressor will be stopped.

Only applies to liquid-to-water heat pumps.

Tariff HP

No (No/Yes)

"Yes" means the function can be activated via remote

control.

Read more in the "Def. Remote Control" section of the

"Installer / Define" chapter.

Tariff HP schedule

This menu bar is displayed if a weekly program has

been defined for the "HP Tariff" function.

For more information, refer to:

• chapter "Weekly Program" for schedule setting.

• section "Def. Remote Control" of the

"Installer / Define" chapter for defining the remote
control function.

SmartGrid block HP

No (No/Yes)

Read more in the "Remote Control /SmartGrid" section

of the "Installer/Define" chapter.

Start at degree minute

-60 (-900...-30

This states the degree minute at which the heat pump

will start.

HS<->DHW time (sec)

120 (30...240)

Time in seconds for which the compressor maintains a

constant speed while switching between heating and

hot water.

Menu: "Installer/Settings/Set". Heat pump.

Содержание EcoZenith i350 L 1x230V





































































































































Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды

CTC Union EcoZenith i350 L 1x230V, Руководство по установке и обслуживанию

Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды