CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 53

Страница: 53 / 132

CTC EcoZenith i360

9. Operation and Maintenance

Automatic bleeder

Safety valve

Manometer

Automatic bleeder

Serial number for registration
and fault reporting behind
magnetic strip.

Solenoid fi lter ball valve

Dirt fi lter for
tap water

Filling valve

Touchscreen

Serial number

Drainage valve

The installation engineer together with the property owner must check that the

system is in perfect operating condition. The installation engineer must show the

switches, controls and fuses to the property owner so that the owner knows how

the system works and how to service it. Bleed the radiators after approximately

three days of operation. Fill with water as needed via the filling valve if the

manometer shows that the system pressure is too low.

Operation stop

The product is turned off using the omnipolar switch. If there is a risk of the water

freezing, all the water should be drained from the heat pump and the heating

circuit.

Draining the tank

The product should be disconnected from the power source while it is being

drained. The draining valve for the low model is situated in the bottom right as

viewed from the front, behind the product’s front panel. For the high model, the

drainage valve is included in the additional pack and the pipe installation engineer

chooses where to connect the valve. Air must be supplied to the closed system.

Boiler and heating circuit bleeding/safety valve

Check around four times a year that the valve is working correctly by manually

turning the control. Check that there is water and not air coming out of the waste

pipe; if air is coming out then the tank will need to be bled. Open the screw on the

automatic bleeder for the first few months; the screw should then be closed to

avoid damaging the bleed valve.

Cleaning the dirt fi lter and solenoid fi lter ball valve

Regularly clean the dirt filter (close off incoming tap water, remove and clean the

filter) and solenoid filter ball valve (close off the flow to the heat pump, remove and

clean the filter).

Содержание EcoZenith i350 L 1x230V





































































































































Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды

CTC Union EcoZenith i350 L 1x230V, Руководство по установке и обслуживанию

Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды