CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 132

background image

123

CTC EcoZenith i360

13.4

Alarm messages

If a fault occurs with e.g. a sensor, an alarm is triggered. A message appears on the

display with information about the fault.

You reset the alarm by pressing the Reset Alarm button on the display. If several alarms

are triggered, they are displayed one after the other. A persisting fault must first be

rectified before it can be reset. Some alarms are reset automatically if the fault ceases.

Alarm messages

Description

[E010] Compressor type ?

This message appears if no information about the compressor type is available.

[E013] EVO off

This message appears when there is a fault with the expansion valve control.

[E024] Fuse blown

This message appears when the fuse (F1, F2) has been triggered.

[E026] Heat pump

This message appears if the heat pump is in alarm mode.

[E027] Communication error

HP

[E063] Comm. err. relay board

[E056] Comm. err. motor

protection

[E086] Comm. err. expansion

card

This message is displayed when the display card (A1) cannot communicate with the

HP control card (A5).

This message is displayed when the display card (A1) cannot communicate with the

relay card (A2).

This message is displayed when the HP control card (A5) cannot communicate with

the motor protection (A4).

This message is displayed when the display card (A1) cannot communicate with

CTC Solar control/Expansion card (A3).

[E035] High pressure switch

The refrigerant’s high pressure switch has been triggered. Press reset and check

whether the alarm recurs. If the fault recurs, contact your installer.

[E040] Low brine flow

Low brine flow is often caused by air in the collector system, especially immediately

following installation. Collectors which are too long can also be a cause. Press

reset and check whether the alarm recurs. Also check the brine filter that has been

installed.

If the fault recurs, contact your installer.

[E041] Low brine temp

Incoming brine temperatures from bore hole/ground loop are too low. Press reset

and check whether the alarm recurs. If the fault recurs, contact your installer to

check the dimensions of the cold side.

[E044] Stop, high compr temp

This message appears when the compressor temperature is high.

Press reset and check whether the alarm recurs. If the fault recurs, contact your

installer.

[E045] Stop, low evaporation

This message appears when the evaporation temperature is low.

Press reset and check whether the alarm recurs. If the fault recurs, contact your

installer.

[E046] Stop, high evaporation

This message appears when the evaporation temperature is high.

Press reset and check whether the alarm recurs. If the fault recurs, contact your

installer.

[E047] Stop, low suct. gas exp.

valve

This message appears when the suction gas temperature is low.

Press reset and check whether the alarm recurs. If the fault recurs, contact your

installer.

[E048] Stop, low evap. exp.

valve

This message appears when the expansion valve’s evaporation temperature is low.

Press reset and check whether the alarm recurs. If the fault recurs, contact your

installer.

«
...
121
122
123
124
125
...
»

Содержание EcoZenith i350 L 1x230V





































































































































Отзывы:

Нет отзывов

Похожие инструкции для EcoZenith i350 L 1x230V

ecoTEC plus 937

Бренд: Vaillant Страницы: 16

Бренд: IBC Страницы: 80

Бренд: elco Страницы: 52

NINFA N LOW NOX 24 MCS

Бренд: Lamborghini Caloreclima Страницы: 144

Prestige Slol 250

Бренд: TriangleTube Страницы: 89

Бренд: A.O. Smith Страницы: 48

Бренд: OSO HOTWATER Страницы: 64

Prestige 24 Excellence

Бренд: ACV Страницы: 48

Бренд: Dunkirk Страницы: 40

Бренд: A.O. Smith Страницы: 12

Бренд: IDEAL Страницы: 8

Бренд: Watts Страницы: 25

Xilo D 20 MC W TOP U/IT

Бренд: LAMBORGHINI Страницы: 32

Бренд: THERMO 2000 Страницы: 59

ATLAS D 30 SI UNIT

Бренд: Ferroli Страницы: 88

ATLAS 25 SI UNIT

Бренд: Ferroli Страницы: 100

Бренд: Viessmann Страницы: 192

Бренд: broag Страницы: 259

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды