CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 115

Страница: 115 / 132

115

CTC EcoZenith i360

12.12 Service

12.12.1

Function test

From this menu, the installer can test the connection

and function of separate components of the heating

circuit. When this menu is activated, all control functions

are stopped. The only protection against incorrect

operation is the pressure sensors and the electric

heater’s overheating protection device. The heat pump

returns to normal operation after 10 minutes of inactivity

or when exiting the "Function Test" menu. When the

menu is opened, all automatic functions are stopped

and testing can be performed.

When you exit the menu, the heat
pump returns to normal operation.

NB: This menu is intended for the
installer only.

12.12.1.1 Test Heating circuit

If several heating circuits have been installed, they will all

be displayed here.

Rad. pump (1-)

Off (On/Off)

Starts and stops the respective radiator pump.

Mixing valve (1-)

Close (Close/Open)

Opens and closes the respective mixing valve.

LED room sensor

Off (On/Off)

The room sensor alarm functions can be controlled from

here. When activated, the respective room sensor’s red

LED comes on steady.

Menu: "Installer/Service".

Menu: "Installer/Service/ Function Test".

Menu: "Installer/Service/ Function Test/Heating Circuit".

Содержание EcoZenith i350 L 1x230V





































































































































Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды

CTC Union EcoZenith i350 L 1x230V, Руководство по установке и обслуживанию

Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды