CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 116

Страница: 116 / 132

116

CTC EcoZenith i360

Menu: "Installer/Service/ Function Test/Heat Pump".

Menu: "Installer/Service/ Function Test/Valves".

12.12.1.2 Test Heat pump

HP Compressor

Off (On/Off)

When the compressor is being function tested, the

brine and charge pump are also operating so that the

compressor does not trigger its pressure switches.

HP Brine Pump/Fan

Off (Off/On)

Function test brine pump or fan (air-to-water heat

pump).

HP Charge Pump

Off (Off/On/ 0...100%)

Function test charge pump 0–100%.

Defrost Manually

Off (Off/On)

When the "Manual defrosting" function is tested, a

defrosting cycle will be performed in the air-to-water

heat pump. Defrosting cannot be stopped once it has

been started and the defrosting programme will be

completed.

Compressor heat

Off (Off/On)

Function test compressor heater.

Drip tray heater

Off (Off/On)

Function test of the condenser tray heater.

Heating Cable

Off (Off/On)

Function test heating cable.

4-way valve (Y11)

Off (Off/On)

Function test 4-way valve (Y11). Fitted to air-to-water

heat pump.

12.12.1.3 Test Valves

The following valves are function tested from this menu:

3-way valve

HS/DHW

12.12.1.4 Test Electric heaters

Tests the electric heaters per phase and step (On/Off).

Electric heater L1A

Off (Off/On)

Electric heater L1B

Off (Off/On)

Electric heater L2A

Off (Off/On)

Electric heater L2B

Off (Off/On)

Electric heater L3A

Off (Off/On)

Electric heater L3B

Off (Off/On)

Electric heater A13

Off (Off/On)

Menu: "Installer/Service/ Function Test/Electric Heaters".

Содержание EcoZenith i350 L 1x230V





































































































































Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды

CTC Union EcoZenith i350 L 1x230V, Руководство по установке и обслуживанию

Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды