CTC Union EcoZenith i350 L 1x230V Скачать руководство пользователя страница 112

Страница: 112 / 132

112

CTC EcoZenith i360

12.11.5

Def. DHW

Extra DHW ext. config.

None(None/NC/NO)

This menu defines the Normally Open (NO) or Normally

Closed (NC) mode for the external control signal when

remotely controlling the function.

For examples of normal mode settings, refer to the

"Def. Remote Control" section of the "Installer / Define"

chapter.

DHW circulation

No (Yes/No/DHW)

“Yes”

the DHW circulation (DHW circ.) with circulation

pump G40 is defined. This functionality option requires

the Expansion Card (A3) accessory for DHW circulation

to be monitored by the product.

“DHW”

option with external DHW circulation pump

which is not controlled by the product. Does not require

expansion card (A3).

DHW circ. ext. config.

None (None/NC/NO)

This menu defines the Normally Open (NO) or Normally

Closed (NC) mode for the external control signal when

remotely controlling the function.

For examples of normal mode settings, refer to the

"Def. Remote Control" section of the "Installer / Define"

chapter.

12.11.6

Def. Diff Thermostat function

Diff Thermostat function

No/Yes

Specify here whether Diff thermostat function is used.

The differential thermostat function is used if you want to

charge your EcoZenith from a water-jacketed stove, or

another heating source.

However, this function cannot be combined with the

same function in a solar heating circuit (when e.g. an

EcoTank is connected to an EcoZenith i360). This is

because the same outlets and sensors are used for

both functions.

Information about the Differential Thermostat function

will be displayed under Operation data.

12.11.7

Def. Electric heater

Tariff EL ext. config.

None (NO/NC/None)

The function can block the electric heater at times of

high electricity tariffs by means of an external signal.

This menu defines the Normally Open (NO) or Normally

Closed (NC) mode for the external control signal when

remotely controlling the function.

For examples of normal mode settings, refer to the

"Def. Remote Control" section of the "Installer / Define"

chapter.

Menu: "Installer/Define/DHW".

Menu: "Installer / Define".

Menu: "Installer / Define / Electric Heater".

Содержание EcoZenith i350 L 1x230V





































































































































Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды

CTC Union EcoZenith i350 L 1x230V, Руководство по установке и обслуживанию

Результаты поиска

Содержание EcoZenith i350 L 1x230V

Отзывы:

Похожие инструкции для EcoZenith i350 L 1x230V

Бренды по названию

Популярные бренды