CLIFFORD MATRIX 70.5X Скачать руководство пользователя | Manualshive

Страница: 27 / 70

background image

© 2006 Directed Electronics—all rights reserved

2

H2/4 GREEN/WHITE (-) factory alarm rearm

This wire sends a negative pulse every time the remote start shuts down or the doors are locked. This can
be used to pulse the arm wire of the vehicle's factory anti-theft device. Use a relay to send a (-) or (+)
pulse to the arm wire.

H2/5 GRAY/BLACK (-) diesel wait-to-start bulb input

Connect this wire to the wire in the vehicle that sends the signal to turn on the WAIT-TO-START bulb in
the dashboard. In most diesels the wire is negative (ground turns on the bulb) and the GRAY/BLACK wire
can be directly connected to the wire in the vehicle. If the vehicle uses a positive wire (12V to turn on the
bulb) a relay must be used to change the polarity. (See

Finding the Wires You Need

section of this guide.)

Here are some common colors of this wire:

■

Chevrolet and GMC trucks - Light blue or dark blue

■

Ford Trucks - Black/pink

■

Dodge Ram Trucks - Orange/black or black/orange

NOTE!

A 1-amp diode must be installed in line on the factory wire between the wait-to-start indicator and

the ECM. (See the following diagram for details.)

«
...
25
26
27
28
29
...
»

Содержание 70.5X







































































Отзывы:

Нет отзывов

Похожие инструкции для 70.5X

Бренд: Viper Страницы: 17

Бренд: BRK electronic Страницы: 2

Бренд: Smartro Страницы: 9

Бренд: La Crosse Technology Страницы: 6

Бренд: Radal Technology Страницы: 4

00123189 RC 150

Бренд: Hama Страницы: 44

Бренд: Prestige Страницы: 6

Бренд: Silvercrest Страницы: 28

Бренд: Silvercrest Страницы: 46

Бренд: Silvercrest Страницы: 62

Бренд: Silvercrest Страницы: 69

Бренд: Silvercrest Страницы: 98

Бренд: Silvercrest Страницы: 140

Бренд: Silvercrest Страницы: 199

CS-2002DC Series III

Бренд: CrimeStopper Страницы: 21

Бренд: Polon-Alfa Страницы: 18

Бренд: LAVVU Страницы: 2

Бренд: SETRONIC VERONA Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды