CLIFFORD MATRIX 70.5X Скачать руководство пользователя | Manualshive

Страница: 38 / 70

background image

© 2006 Directed Electronics—all rights reserved

3

programmer interface, 3-pin black plug

The black 3 pin port is provided for programming the unit using the Bitwriter (p/n 998T). When using the
Bitwriter, it is possible to configure any and all of the programmable functions as well as lock the Remote
Control and System Features Learn Routines so that unauthorized users cannot change the configuration or
program remote controls to the unit.

When the learn routines have previously been programmed using the Bitwriter, they may have
been locked. Before proceeding with reprogramming the learn routines, they must be unlocked
with the Bitwriter - this cannot be done manually with the Valet switch.

shock sensor harness, 4-pin connector

GREEN (-) multiplex input, zone 4

Inputs shorter than 0.8 seconds will trigger the Warn Away response, while inputs longer than 0.8 seconds
will trigger full alarm sequence and report Zone Four. If installing an optional Directed Electronics dual stage
sensor, connect to the green wire as shown below. The diagram below eliminates the need for diodes to
isolate the sensors.
Diagram for adding optional Directed Electronics dual stage sensor to green wire (Zone 4):

«
...
36
37
38
39
40
...
»

Содержание 70.5X







































































Отзывы:

Нет отзывов

Похожие инструкции для 70.5X

Бренд: Falcon Страницы: 7

Бренд: Velleman Страницы: 48

Бренд: ZEBON Страницы: 2

Бренд: Omega Страницы: 12

Бренд: Autostart Страницы: 11

Prestige 128-8601

Бренд: Audiovox Страницы: 8

Intelliguard 750

Бренд: Directed Electronics Страницы: 45

Бренд: Directed Electronics Страницы: 55

Бренд: Paser Страницы: 4

Бренд: RadioLink Страницы: 21

Бренд: Code Alarm Страницы: 9

Бренд: Eurotops Страницы: 15

Бренд: Zetronix Страницы: 13

Бренд: Accele Страницы: 4

Бренд: AUTHOR Alarm Страницы: 32

Бренд: Navox Страницы: 23

Бренд: Navox Страницы: 26

Atlanta 1889-19

Бренд: Paragon Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды